Milwaukee SDS+ Drill Bits
Drilling fixing holes in concrete or brick? Milwaukee SDS drill bits work with rotary hammers to break through masonry.
For sparkies, plumbers and fitters, Milwaukee SDS Plus drill bits cover fixing holes and service routes. Match the shank to your drill, check usable drilling depth rather than overall length, then choose the diameter your fixing needs.
What Jobs Are Milwaukee SDS Drill Bits Best At?
- Drill fixing holes in sound concrete and solid brick for cable tray brackets, pipe clips and containment, matching the bit diameter to the fixing specification.
- Fit kitchen units, shelving and sanitaryware by drilling accurately sized holes for Wall Plugs, with the hammer action switched off where the substrate requires it.
- Run cables and small pipework through masonry walls using a bit with enough working length to clear the full wall thickness.
- Drill repeated anchor holes in concrete for brackets and supports, clearing dust between holes and checking bit wear to maintain the specified hole size.
Choosing the Right Milwaukee SDS Drill Bits
Buy for the fixing, the wall and the drill chuck; diameter alone will not tell you whether a bit is right.
1. Match the Shank to Your Drill
If your rotary hammer has an SDS Plus chuck, choose an SDS Plus bit. SDS Max is a different fitting, not simply a larger drilling diameter. Check the drill's recommended capacity as well; a bit fitting the chuck does not mean the machine is suited to driving it.
2. Buy the Diameter Your Fixing Specifies
A Milwaukee 6mm SDS bit, Milwaukee 8mm SDS bit and Milwaukee 10mm SDS bit are not interchangeable when installing fixings. Follow the plug or anchor instructions rather than guessing from the screw size. For mixed installation work, Milwaukee SDS Plus Drill Bit Sets keep several fixing sizes together.
3. Check Working Length, Not Just Overall Length
If you need to pass through a wall, the usable drilling length must cover the full thickness, including finishes. A Milwaukee long SDS bit gives extra reach, but use a shorter bit where possible for controlled starts and less flex.
4. Check the Cutter Design
Milwaukee MX4 SDS Plus bits use a four-cutter head, which helps maintain round holes and reduces snagging if reinforcement is encountered. Do not assume every Milwaukee SDS drill bit has that head design. Check the individual specification, and never treat a reinforced-concrete rating as permission to drill through structural steel.
Who Uses Milwaukee SDS Drill Bits?
Sparkies use these bits for containment fixings and cable routes, while plumbers reach for longer sizes when taking small services through masonry. Kitchen fitters and maintenance teams keep common fixing diameters handy for brackets and wall-mounted fittings. Groundworkers use suitable sizes for concrete anchors, following the anchor manufacturer's drilling and hole-cleaning instructions.
The Basics: Understanding SDS Drill Bits
SDS bits work with a rotary hammer's striking mechanism. The shank and cutting head both matter when matching the bit to the machine and the material.
1. The Shank Transfers Rotation and Hammer Blows
The grooved SDS shank locks into a compatible chuck while allowing the bit to move forwards and backwards under impact. Check the chuck fitting and drilling capacity when pairing bits with Milwaukee M18 SDS Drills. Do not clamp an SDS shank in a standard three-jaw chuck for hammer drilling.
2. The Head Breaks Material and the Flutes Remove Dust
The carbide cutting head breaks masonry under impact, while the spiral flutes carry spoil out of the hole. On deeper holes, withdraw the rotating bit periodically as instructed to clear debris. Forcing a packed hole adds heat and load without improving progress.
Accessories for Cleaner SDS Drilling
Sort dust capture and shank care before starting repeated masonry drilling; both help avoid preventable stoppages.
1. Compatible Drilling Dust Extraction Attachment
Use a drilling shroud or on-tool extractor suited to the drill, bit diameter and working length. Connect it to suitable extraction where required by your dust-control assessment. Check Milwaukee SDS Plus Accessories for compatible options rather than assuming one attachment fits every machine.
2. Manufacturer-Specified SDS Shank Grease
Where the drill manual requires it, apply a light film of the specified grease to a clean shank. This reduces wear at the chuck interface. Do not pack the chuck with grease; excess collects abrasive masonry dust.
Choose the Right Milwaukee SDS Drill Bits for the Job
Start with the required hole size, then check reach, head design and machine compatibility.
| Your Job | Bit Type | Key Features |
|---|---|---|
| Drilling for a plug that specifies a 6mm hole | 6mm SDS Plus bit | Correct diameter and enough working length for the specified embedment and clearance. |
| Installing fixings requiring 8mm or 10mm holes | 8mm or 10mm SDS Plus bit | Diameter matched exactly to the fixing instructions, not the screw diameter. |
| Repeated concrete fixing holes | MX4 four-cutter SDS Plus bit | Four-cutter head to support round holes; check the concrete rating and drill capacity. |
| Passing small services through a thick masonry wall | Long SDS Plus bit | Usable drilling length greater than the measured wall thickness, including finishes. |
Common Buying and Usage Mistakes
- Buying by overall length can leave you short halfway through a wall. Check the usable drilling length before ordering.
- Choosing the hole size from the screw diameter can leave a plug loose or impossible to insert. Use the fixing manufacturer's specified drill diameter.
- Leaning heavily on the drill can increase heat, binding and wear. Apply steady pressure and let the hammer mechanism do the work.
- Using hammer action indiscriminately can break out hollow blocks, damage tiles or enlarge holes in weak masonry. Select the bit and drilling mode for each layer.
- Drilling without checking for concealed services risks striking cables or pipes. Check drawings where available, scan appropriately and establish a safe drilling position first.
SDS Plus vs SDS Max vs Straight-Shank Masonry Bits
SDS Plus for Fixings and Installation Work
Choose SDS Plus for compatible rotary hammers used on everyday masonry fixing holes and smaller service routes. It suits installation work without the bulk of a larger SDS Max machine, but stay within the drill's recommended diameter range.
SDS Max for Larger Rotary Hammers
Milwaukee SDS Max Bits use a larger shank for compatible heavy-duty machines. Choose that system for larger drilling work where the machine and bit specifications call for it; the bits do not fit an SDS Plus chuck directly.
Straight-Shank Bits for Conventional Chucks
A suitable straight-shank masonry bit works in a conventional drill chuck for occasional holes in appropriate masonry. For repeated concrete drilling, a rotary hammer and compatible SDS bit are generally the more practical combination.
Maintenance and Care
Clear the Flutes After Use
Let the bit cool, then remove packed debris with a suitable brush and controlled dust extraction. Avoid blowing masonry dust into the air with compressed air.
Keep the Shank Clean
Wipe grit from the shank before insertion and follow the drill manual's lubrication instructions. A dirty shank carries abrasive debris straight into the chuck.
Check for Damage and Wear
Replace bits with chipped carbide, a bent shaft or damaged retaining grooves. Check worn bits before critical anchor work; do not improvise sharpening where the specified cutting geometry matters.
Store Dry and Protect Long Bits
Dry bits before putting them away and keep long lengths supported in a case or rack. Leaving them loose beneath heavy tools risks bent shafts and damaged cutting heads.
Your Milwaukee SDS Drill Bit Range, Ready to Go
ITS stocks the full Milwaukee SDS drill bit range, covering fixing diameters, longer drilling lengths and MX4 options. Stock is held in our own warehouse, ready for next-day delivery. Check the individual listing for current availability and delivery options before booking the job.
Milwaukee SDS Drill Bits FAQs
What is a Milwaukee MX4 SDS bit?
MX4 is Milwaukee's four-cutter SDS Plus masonry drill bit design. Its carbide head is designed for concrete drilling, including reinforced concrete where specified, and helps reduce snagging on reinforcement. It does not replace a rebar cutter or authorise cutting structural reinforcement; stop and establish an approved route if steel obstructs the hole.
What size SDS bit for a 6mm plug?
A standard 6mm wall plug normally requires a 6mm drill bit, but check the plug instructions for the substrate, drilling mode and depth. Drill straight and avoid enlarging the entrance by rocking the tool. Clean the hole as specified before inserting the plug.
Are Milwaukee SDS bits 4 cutter?
Milwaukee MX4 SDS Plus bits have a four-cutter head, but that does not mean every Milwaukee SDS bit does. Check the individual product specification for cutter count and head construction before ordering replacements.
How do you stop an SDS bit wandering?
Mark the hole clearly, hold the drill square and start slowly with a short bit where possible. Establish a shallow seating point before increasing speed and using the appropriate hammer setting. On tiles or other brittle finishes, use a suitable tile bit without hammer action first, then change to the masonry bit once through the finish.
What length SDS bit do I need for a cavity wall?
Measure both masonry leaves, the cavity and any finishes, then choose a bit whose usable drilling length exceeds that total. Overall bit length includes the shank, so it is not the available reach. Check both sides for services and obstructions, and reduce feed pressure near breakthrough to limit damage to the far face.
Are Milwaukee SDS bits carbide tipped?
Milwaukee SDS masonry drill bits use carbide cutting elements to handle abrasive masonry and hammer impact. Head construction varies by range, so check whether the specific bit uses a carbide tip or a full-carbide head rather than assuming they are identical.
Can Milwaukee SDS bits drill granite?
Some are rated for natural stone, but check that the particular bit is suitable for granite. Rough structural stone and a polished granite worktop are different jobs. For polished surfaces or brittle edges, use specialist stone-drilling tooling and its specified method rather than starting with hammer action.
Do SDS drill bits need cooling?
Standard SDS masonry bits are generally used dry. Clear debris regularly, avoid excessive pressure and pause if the bit becomes very hot or progress drops sharply. Do not quench a hot carbide head in water, as thermal shock can damage it. Only use water where the bit, machine and drilling method are expressly designed for it.