OX Tools More Accessories
OX power tool accessories more covers the site extras that keep drills, mixers and fixings working properly through hard daily graft.
When the main tool is fine but the job still slows up, it is usually the accessory letting you down. This OX range covers the practical bits trades actually burn through, from OX mixing paddles for clean, lump-free plaster and adhesive, to fixings and consumables that stand up to proper site use. If you are topping up van stock or replacing worn gear before it costs you time, start here and get the right accessories for the work ahead.
What Are OX Power Tool Accessories More Used For?
- Mixing plaster, bonding, tile adhesive and similar materials with an ox mixing paddle when hand mixing is too slow and leaves dry pockets in the bucket.
- Keeping cordless drills and drivers useful across first fix, kitchen fitting and snagging jobs by swapping in the right bits, fasteners or attachments for the task.
- Reloading nail guns and replacing site consumables so joiners, roofers and framing crews can keep moving without stopping for mismatched fixings.
- Handling the smaller but essential tool add-ons that wear out first on busy jobs, especially when the main machine is still sound but the working end is finished.
Choosing the Right OX Power Tool Accessories
Match the accessory to the material and the tool first. That saves more grief than buying whatever is nearest the till.
1. Pick the Accessory for the Material
If you are mixing plaster or adhesive, use a proper ox mixing paddle with the right shape and size for the bucket and mix volume. If you are driving fixings or drilling out timber, switch to the accessory made for that job instead of forcing one bit to do everything badly.
2. Check the Shank and Tool Fit
Before you buy, check what your drill, driver or mixer actually takes. If the shank or holder does not match, you will either be heading back to the van for an adaptor or wasting time trying to make the wrong kit work.
3. Buy for How Often You Graft
If it is a one-off room, standard consumables may see you through. If you are on plaster, timber or fixings every day, buy the accessories that can take repeat use and keep a spare in the van because these are the bits that always wear out first.
4. Do Not Ignore Pack Size and Replacements
If you get through nails, bits or paddles regularly, buy enough to cover the job and the next one. Running short on a cheap accessory is a daft way to stop a full day of paid work.
Who Uses These on Site?
- Plasterers and dryliners reach for ox mixing paddles when they need a smooth, consistent mix for skim, bonding or adhesive without dragging half-set material round the tub.
- Chippies and kitchen fitters keep these accessories close for driving fixings, refreshing worn bits and keeping drills earning their keep through first fix and final snagging.
- Roofers, timber framers and second fix teams use nail gun consumables and related accessories because the wrong nails or poor feed soon waste time and jam the gun.
- General builders and maintenance teams buy from this part of the range when they need the smaller working parts that actually get used up before the tool itself does.
The Basics: Understanding OX Power Tool Accessories
This part of the range is about what the tool actually does at the working end. Get that bit right and the job goes quicker, cleaner and with less strain on the machine.
1. Mixing Accessories
A mixing paddle pulls material through the bucket so plaster, adhesive or compound blends evenly. The right paddle shape helps stop dry pockets, cuts mixing time and gives you a more usable mix on the wall or floor.
2. Driving and Drilling Accessories
Bits and drill accessories transfer the tool's torque or cutting action into the fixing or material. If the fit is poor or the accessory is worn, you lose grip, round screws off and put more stress on the drill than necessary.
3. Fastening Consumables
Nails and similar consumables need to match the gun and the job. The correct type feeds cleanly, fixes securely and saves you dealing with jams, bent strips and wasted stock halfway through the run.
OX Accessories That Keep the Job Moving
These are the add-ons worth having sorted before you start, not after the tool stops being useful.
1. Spare Mixing Paddles
Keep a spare paddle if you regularly mix plaster, adhesive or compound. One bent, caked-up or undersized paddle can ruin the mix and leave you wasting time scraping lumps out by hand.
2. Bit Holders and Driver Bits
A fresh set of holders and bits saves rounded screws, cam-out and that usual site nonsense where a tired bit slips just as you are finishing decent work.
3. Drill Bits
If your drill is working harder than it should, the cutting edge is often the problem. Keeping the right drill bits to hand means cleaner holes, less heat and less punishment on the tool.
4. Nail Gun Consumables
Wrong nails or poor-quality strips are an easy way to jam a good gun. Stock the right consumables and you avoid stoppages when the run needs finishing that day.
Choose the Right OX Power Tool Accessories for the Job
Use this quick guide to narrow the range down before you order.
| Your Job | Category or Type | Key Features |
|---|---|---|
| Mixing plaster, bonding or tile adhesive | OX mixing paddle | Proper paddle profile, drill or mixer compatibility, size to suit bucket and mix volume |
| Driving large numbers of screws on first or second fix | OX screwdriver bits and holders | Correct tip type, secure fit in the screw head, holders that stand up to repeated impact use |
| Drilling timber, masonry or sheet material | OX drill accessories | Bit style matched to material, clean cutting edge, shank that suits your drill or driver |
| Running a nail gun for framing, roofing or fix out | OX nail gun nails | Correct gauge and collation, gun compatibility, pack size that covers the run without stopping |
| General van restock for day to day site use | Mixed OX consumables and accessories | Most-used wear parts, proper compatibility, enough stock to avoid losing time on simple replacements |
Common Buying and Usage Mistakes
- Buying a mixing paddle that is too small for the bucket or mix volume leaves dry pockets and uneven material. Match the paddle size to the amount you actually mix.
- Using worn screwdriver bits because they still sort of fit usually ends with stripped heads and wasted fixings. Replace bits early once they start slipping.
- Guessing nail gun compatibility is a fast way to cause feed problems and jams. Check the nail type and gun requirements before loading up.
- Treating accessories as an afterthought means the main tool gets blamed for poor performance. Often the drill, driver or nailer is fine and it is the worn accessory causing the problem.
- Not keeping spares on site turns a cheap missing consumable into a dead hour. If you use it every day, keep a backup in the van.
Mixing Paddles vs Screwdriver Bits vs Nail Gun Nails
Mixing Paddles
Best for wet trades mixing plaster, adhesive and compounds where consistency matters. They are no use for fixing or drilling, but if the mix is wrong, the whole job starts badly.
Screwdriver Bits
Best for repeated screwdriving on first fix, second fix and fitting work. They give you control and speed, but only if the tip matches the fixing properly and the bit is not already rounded off.
Nail Gun Nails
Best where speed matters on timber runs, roofing and framing. Faster than loose fixing methods, but they must match the gun and job or you will spend more time clearing jams than fixing out.
Drill Accessories
Best when you need to make the hole before anything else happens. Choose these when the material is the issue, not the fixing, and match the bit style to what you are drilling through.
Maintenance and Care
Clean Mixing Paddles Straight Away
Do not leave plaster or adhesive to set on the paddle. Clean it straight after use or next time it goes in the bucket it will throw lumps through the mix and work the drill harder.
Bin Worn Bits Early
If a driver bit starts camming out or chewing screw heads, it is done. Hanging on to it only damages fixings and slows the job.
Keep Consumables Dry and Sorted
Store nails, bits and smaller accessories in dry cases or boxes. Damp, dirt and loose storage soon lead to corrosion, damaged tips and wasted time hunting for the right piece.
Check for Bent or Damaged Working Ends
A bent paddle or damaged bit does not wear back into shape. Inspect the working end before use and replace it if it is out, especially where accuracy or mix quality matters.
Replace Cheaply, Protect the Main Tool
Accessories are meant to wear before the machine does. Replacing a tired accessory on time is a lot cheaper than cooking a drill motor or jamming up a nail gun on a live job.
Why Shop for OX Power Tool Accessories More at ITS?
Whether you need a fresh paddle for the next skim coat, replacement bits for daily fixing work, or nail gun consumables for a timber run, we stock the full OX range in depth. That includes OX screwdriver bits and bit holders, OX drill bits, OX nail gun nails and accessories and OX angle grinder discs. It is all held in our own warehouse, in stock and ready for next day delivery.
OX Power Tool Accessories More FAQs
What is a mixing paddle used for?
A mixing paddle is used for blending plaster, bonding, mortar, tile adhesive, levelling compound and similar materials with a drill or mixer. It gives you a more even mix than doing it by hand, with fewer dry pockets and less wasted material.
What other power tool accessories does OX make?
OX covers a broad spread of site consumables and working-end accessories, including mixing paddles, screwdriver bits, drill accessories, nail gun nails and grinder consumables. It is the sort of range you buy when the tool itself is fine but the job needs the right attachment or replacement part.
Are OX power tool accessories any good?
Yes, they are a solid choice for regular trade use. OX kit is generally bought by trades who want accessories that cope with day-to-day site work without paying for gimmicks, especially for mixing, fixing and general consumable restocks.
What paddle do I need for mixing plaster?
For plaster, use a paddle suited to lighter wet mixes and match the size to the bucket and amount you are mixing. Too small and it drags forever without fully blending the material. Too large and it overloads the drill and throws mix about.
What accessories fit a cordless drill?
That depends on the chuck or holder fitted to your drill. Standard cordless drills usually take round or hex shanks in the chuck, while impact drivers use quick-change hex accessories. Always check the shank type and the load your tool is built to handle before mixing or drilling.
