OX Tools Power Tool Accessories
OX power tool accessories cover the consumables that keep drills, grinders and mixers earning their keep on site day after day.
When the tool is sound but the accessory lets you down, that is when holes wander, cuts burn and mixes go off wrong. OX power tool consumables are the bits you buy for real graft, from ox drill bits and ox diamond blades to ox screwdriver bits, mixing paddles and ox angle grinder discs. If your kit gets used hard on brick, block, steel and fixings, start with the right accessory and get the job moving.
What Are OX Power Tool Accessories Used For?
- Drilling into brick, block and concrete for fixings, tray, clips and anchor points is where ox drill bits earn their keep, especially when you need clean holes that do not chew themselves out halfway through the day.
- Cutting paving, slabs, lintels, steel sections and masonry on site is exactly what ox diamond blades and ox angle grinder discs are bought for, saving time when there is no room for slow, messy cutting.
- Driving screws into stud, timber, sheet material and first fix hardware is easier with ox screwdriver bits that hold up under repeated impact instead of rounding off after a handful of fixings.
- Mixing plaster, adhesive, mortar, levelling compound or tile adhesive in buckets and tubs is what mixing paddles are for, giving a proper even mix without dry pockets left at the bottom.
- Stocking the van with the right consumables for the week helps avoid wasted trips, and ranges like OX power tool accessories cover the site basics that keep the main tools working.
Choosing the Right OX Power Tool Accessories
Sorting the right one is simple: match the accessory to the material first, then the tool you are actually using.
1. Match the Accessory to the Material
If you are drilling masonry, buy masonry bits. If you are cutting metal, use the right cutting disc. Do not try and make one accessory cover every job, because that is how you end up with slow progress, burnt edges and wasted consumables.
2. Check the Tool Fitment
Before you buy, check shank type, disc diameter, bore size and whether the accessory suits a drill driver, impact driver, grinder or mixer. A decent accessory is no use if it does not fit the machine in your hand.
3. Buy for Volume of Work
If it is just a one-off snagging job, a small pack will do. If you are on first fix, hard landscaping or repeated cut and drill work all week, buy the tougher option or bigger pack and save yourself running short by lunchtime.
4. Think About Finish as Well as Speed
For rough openings and fast site cuts, speed matters most. For visible edges, fixings that need to sit properly, or mixes that must go down right first time, choose the accessory that gives control and consistency, not just the fastest bite.
Who Uses These on Site?
- Sparkies use ox drill bits and screwdriver bits for cable runs, back boxes and containment, because blunt bits and chewed tips slow first fix right down.
- Brickies, landscapers and groundworkers reach for ox diamond blades and grinder discs when they are trimming blocks, slabs and kerbs and need cuts that stay straight without burning through discs too quickly.
- Plasterers, tilers and flooring lads rely on mixing paddles for adhesive, skim and compound, because hand mixing never gives the same consistency once you are doing it day in, day out.
- Joiners and general builders keep a range of ox power tool consumables in the van for fixing timber, sheet and metalwork, especially when the job changes halfway through the day and you still need to crack on.
- Roofers and framing crews also use OX nail gun nails and accessories when speed matters and hand fixing every run would waste half the shift.
The Basics: Understanding Power Tool Accessories
These are the working ends of your tools. The drill, grinder or mixer provides the power, but the accessory decides how cleanly, quickly and accurately the job gets done.
1. Drill Bits Cut by Material Type
A masonry bit is shaped to hammer through brick and block, while other bit types are made for timber or metal. Get this wrong and you will either make no progress or ruin the bit before the first few holes are done.
2. Blades and Discs Are Chosen by What You Are Cutting
Diamond blades are for hard materials like masonry, stone and concrete, while grinder discs vary between cutting, grinding and finishing. The right disc gives a cleaner result and puts less strain on the grinder.
3. Paddles Mix Properly Under Load
A mixing paddle pulls material through the bucket so plaster, adhesive or compound blends evenly. That means fewer lumps, less waste and a mix that actually goes on as it should when you start applying it.
Useful Extras to Keep Your OX Accessories Working
A few sensible add-ons save wasted time, broken consumables and repeat trips back to the van.
1. Bit Holders
A proper bit holder gives you better reach and keeps driver bits sitting properly, which matters when you are sinking fixings into awkward corners or overhead and do not want bits slipping out every other screw.
2. Spare Cutting Discs and Blades
Do not start a cutting job with one disc and blind optimism. Keeping spare grinder discs or diamond blades in the van means you are not stuck halfway through a run of slabs or steel when the first one is spent.
3. Mixing Buckets
A decent clean bucket matters more than most lads admit. Old set material in the bottom ruins fresh mixes, so keeping the right tubs alongside your paddles saves lumps and waste.
4. Drill Bit Sets
Buying bits as a set covers the sizes you actually burn through on site. It also stops the usual problem of having every odd size except the one you need for the fixing in your hand.
Choose the Right OX Power Tool Accessories for the Job
Use this quick guide to match the accessory to the work in front of you.
| Your Job | Category or Type | Key Features |
|---|---|---|
| Drilling fixing holes into brick and block | OX drill bits | Masonry-focused cutting edges, clean hole drilling, sizes that suit common site fixings |
| Trimming slabs, pavers or masonry products | OX diamond blades | Fast cutting through hard materials, better edge control, suited to regular site use |
| Cutting or grinding steel and metal sections | OX angle grinder discs | Choose the right disc for cutting or grinding, check diameter and bore before buying |
| Driving large runs of screws on first fix or fit out | OX screwdriver bits and bit holders | Impact-ready options, secure bit fit, less rounding on repeated fixings |
| Mixing adhesive, skim or levelling compound | OX mixing paddles | Even material blending, less lumping, better consistency in tubs and buckets |
Common Buying and Usage Mistakes
- Buying by tool alone instead of material is a common mistake. A bit or disc might fit the machine but still be wrong for the job, which means slow cutting, poor holes and a consumable ruined early.
- Ignoring size and fitment causes no end of grief. Always check disc diameter, bore, shank and bit type before ordering, or you will be unpacking gear that never had a chance of fitting properly.
- Trying to stretch worn accessories too far wastes more time than it saves. Once bits are blunt or discs are spent, the tool works harder, the finish gets worse and the chance of breakage goes up.
- Using the cheapest option for heavy site work usually backfires. If you are drilling, cutting or driving fixings all week, buy consumables suited to repeated trade use rather than treating them like a one-off DIY purchase.
- Starting a mixing job with the wrong paddle or dirty bucket leads to poor consistency. That shows up later when adhesive drags, plaster lumps or compound goes down unevenly.
Drill Bits vs Diamond Blades vs Screwdriver Bits
OX Drill Bits
These are for making holes cleanly and at the right size for fixings, anchors and services. Buy these when accuracy matters and you are working into brick, block, timber or metal depending on the bit type.
OX Diamond Blades
Diamond blades are the choice for cutting masonry, slabs and other hard materials where a standard disc would wear too fast. They are about fast, controlled cutting rather than drilling or driving.
OX Screwdriver Bits
These are for repeated fixing work with drill drivers and impact drivers. If your day is mostly screws into timber, sheet or hardware, this is the accessory that takes the hammering, not the tool chuck.
OX Mixing Paddles
Mixing paddles are for preparation rather than cutting or drilling. Use them when the finish depends on getting plaster, adhesive or compound blended properly before it ever touches the wall or floor.
Maintenance and Care
Clean Off Dust and Residue
Wipe bits, blades and paddles down after use, especially after mixing jobs or wet cutting. Dried-on material throws performance off and makes it harder to spot wear before the next shift.
Store Consumables Properly
Keep accessories dry and separated in cases or tubs rather than loose in the van. It stops edges getting knocked about and helps you find the right size without rummaging through damaged gear.
Replace Worn Pieces Early
Do not wait until a bit is completely dead or a disc is down to nothing. Replacing consumables at the right time keeps cut quality up and stops the tool working harder than it needs to.
Check for Cracks, Chips and Bent Shanks
Give cutting and drilling accessories a quick once-over before use. If a disc is cracked or a bit shank is bent, bin it and move on, because that failure will happen under load, not while it is sitting safely in the box.
Keep Mixing Gear Clean Straight Away
With paddles especially, clean them before plaster, adhesive or mortar goes off. Leave it too long and you spend more time chipping dried muck off than you would have spent washing it properly.
Why Shop for OX Power Tool Accessories at ITS?
Whether you need a fresh pack of bits, new ox diamond blades, mixing paddles or site-ready ox power tool consumables, we stock the full range in one place. That means the sizes, types and accessories trades actually use, all held in our own warehouse and ready for next day delivery.
OX Power Tool Accessories FAQs
What power tool accessories does OX make?
OX covers the main site consumables most trades actually get through, including drill bits, diamond blades, screwdriver bits, bit holders, mixing paddles, grinder discs and other fitting accessories. It is the sort of range built for drilling, cutting, grinding, driving and mixing rather than oddball extras you never use.
Are OX power tool accessories any good?
Yes, for trade use they are a solid shout. They are made for regular site work, not just light weekend jobs, so you are getting consumables that can take repeated drilling, cutting and fixing without giving up straight away. As ever, the real trick is buying the right accessory for the material and tool.
What is a diamond blade used for?
A diamond blade is used for cutting hard materials like concrete, block, brick, stone, paving and similar products. It is what you reach for when a standard abrasive disc would wear too quickly or leave a rougher cut. On site, that usually means grinders and saws doing masonry and slab work.
What drill bits do I need for masonry?
You need proper masonry bits for brick, block and concrete, and the exact type depends on the tool and the job size. For general drilling into walls for fixings, use masonry bits that match your drill and the fixing diameter. If the material is harder or the holes are bigger, step up to the appropriate heavier-duty bit and drill combination.
What is a mixing paddle used for?
A mixing paddle is used with a drill or dedicated mixer to blend plaster, mortar, adhesive, paint, levelling compound or similar materials. It saves time, gives a more even mix and stops dry pockets sitting at the bottom of the bucket where they ruin the job later.
Will these accessories hold up to proper site use?
They are built for trade work, yes, but consumables are still consumables. Used on the right material, at the right speed, and not pushed past their limits, they will do the job properly. Use the wrong bit in the wrong material and even good gear will look poor fast.
Do I need different accessories for drilling, cutting and fixing?
Yes, absolutely. A drill bit, a cutting disc and a driver bit all do completely different jobs, and trying to make one stand in for another is a waste of time and money. Match each accessory to the exact task and the tool will work better for longer.
