Milwaukee Cable Staples
Cable staples are collated fixings used to secure electrical and data cables to timber surfaces. Designed for cordless staplers, they offer fast, consistent results without crushing insulation — perfect for neat cable routing during first fix.
What Are Cable Staples Used For?
Cable staples are built to hold electrical wires flat to joists, noggins or studwork without pinching or kinking. They’re faster and cleaner than hammer-in clips, especially for long cable runs or overhead work.
- Fixing Twin & Earth Cables – Keep 1.0mm² to 2.5mm² cable secure along joists, beams or framing.
- Running Data or Alarm Lines – Pin lightweight network or alarm cables into place along timber battens.
- Routing Signal or Audio Cabling – Secure low-voltage AV or control cabling in smart home installs.
- Replacing Cable Clips – Fire staples faster and more consistently than hand-placed clips.
Who Uses Cable Staples?
Cable staples are widely used by electricians, AV installers and smart home teams working on first fix installs and structured cabling jobs.
- Electricians – Pin twin & earth across floors, ceilings and within stud partitions at speed.
- Data Installers – Use staples for Cat5/Cat6 trunk runs or patch lead drops across multiple zones.
- Security Engineers – Staple PIR, door contact or sensor wires without over-driving or damaging insulation.
- AV Contractors – Secure HDMI, speaker wire or home control cable discreetly inside walls or timber voids.
What Jobs Are Cable Staples Best At?
They’re the fastest, neatest way to secure cable on timber-based surfaces — especially for overhead work or where visual finish matters after boarding up.
- First Fix Cable Routing – Run mains, data or AV cable neatly and secure during stud and joist installs.
- Overhead Joist Fixing – Fire into ceilings or above-head timber runs without needing ladders or clips.
- Drop Cables to Sockets or Faceplates – Hold final fix lines in place to stop movement before boarding.
- Sensor or Alarm Cabling – Keep thin cable tight along doors, corners or soffits without sag or slack.
- Neat Cable Trunking Prep – Pre-hold cable before applying trunking or duct covers.
How to Choose the Best Cable Staples
Pick staples that match your cable width, insulation thickness and tool compatibility to avoid crush or split risk.
1. Cable Type
Choose staple sizes that suit your main cable run — smaller for 1.0mm², larger for 2.5mm² twin & earth or multi-cable clamps.
2. Staple Depth
Leg length must hold the cable snug without flattening it — too short won’t grip, too long may damage sheathing.
3. Staple Material
Galv is typical for dry installs. Stainless is safer in damp or humid areas. Some versions include plastic guides for extra spacing.
4. Stapler Compatibility
Always match staple dimensions to your Milwaukee cable stapler. Check leg spacing, length and magazine spec.
5. Fixing Surface
Cable staples are for timber only — avoid block, brick or plaster unless pre-fixed with batten or ply.
Cable Staple Accessories & Add-Ons
- Reload staple packs for long cable runs or multiple circuits
- Depth guides and driver tips to prevent over-penetration
- Battery staplers, kits and maintenance gear for repeat jobs
FAQs
Can I use cable staples on brick walls?
No — they’re for timber only. Use battens or trunking if working on masonry, and screw in surface clips instead.
Will staples crush the cable insulation?
Not if correctly sized and set. Use depth-limited staplers and avoid overdriving — especially with twin & earth or Cat6.
Are Milwaukee cable staples reusable?
No — once fired, they bend to shape and should be replaced if pulled. Always use new staples for consistent pressure.
Do I need a specific stapler for these?
Yes — Milwaukee cable staples are built for use with compatible cordless cable staplers. Check the product for sizing and approval.
What’s the benefit over clips?
Speed. Staples fire in instantly, hold flatter and don’t risk over-hammering or skewed clips — especially overhead or one-handed.
