DEWALT CABLE STAPLES
DeWalt cable staples are made for fast, tidy cable fixing without crushing the run, ideal for first fix wiring, data work, and repeat clip jobs.
If you're stapling twin and earth, data cable or low voltage runs all day, use the staples that actually match the gun and cable size. These DeWalt electricians staples are built for DeWalt cable tackers, giving consistent drive, proper hold and cleaner fixing work with less snagging and fewer damaged cables. If you need cable staples for DeWalt stapler jobs that stay neat and move quickly, this is the place to start. You can also browse Nails, Pins & Staples by Compatibility if you're matching fixings to a specific tool.
What Are DeWalt Cable Staples Used For?
- Fixing twin and earth neatly along joists and studwork is where DeWalt cable staples earn their keep, especially on first fix when you need speed without crushing the sheath.
- Running data, alarm and low voltage cable through lofts, risers and plant rooms is quicker with cable staples for DeWalt stapler use, as they hold the run consistently and save endless hand clipping.
- Securing repeat cable runs in domestic rewires, plot work and commercial fit outs is easier when the staple crown and leg are matched properly to the cable diameter and the DeWalt gun.
- Tidying up final routes around meter boards, cupboards and service voids is simpler with insulated cable staples that grip the cable without leaving it loose or battered.
- Speeding up high volume fixing on site matters when you're doing one room after another, and DeWalt cable stapler staples help keep spacing, finish and holding power more consistent than mixed loose fixings.
Choosing the Right DeWalt Cable Staples
Sorting the right staples is simple: match the staple to the cable and the gun, not what happens to be left in the van.
1. Match the Cable Size Properly
If the staple is too tight, you risk pinching or marking the cable. If it is too loose, the run will sit proud and look rough. Check the cable size first, especially if you are swapping between twin and earth, coax, data or alarm cable.
2. Buy for the Exact DeWalt Tool
Do not assume all dewalt cable tacker staples fit every gun in the range. If you are using an electricians stapler, buy the staples listed for that model so you get proper feed, drive depth and holding power.
3. Think About the Volume of Work
If you are doing snagging or a few short runs, a smaller pack is fine. If you are wiring plots or long commercial runs, buy enough packs to stay on the tool all day because running out halfway through first fix just slows the whole job down.
4. Use Insulated Staples Where Specified
If the job calls for insulated cable staples, stick to that requirement. They help protect the cable jacket and are the right choice where the fixing needs to hold firm without biting straight into the outer sheath.
Who Uses These on Site?
- Sparkies use DeWalt cable staples for first fix cable runs through joists, rafters and stud walls because they are faster than hand-fitted clips and give a neater, more even finish.
- Data and security installers reach for them when fixing CAT cable, alarm wire and similar low voltage runs where a tidy route and repeat spacing make the job look right.
- Maintenance teams keep them in the van for adding short cable runs, replacing damaged sections and sorting small works without dragging out bags of mixed clips and pins.
- House bashers and site electricians swear by them on plot work, where one compatible staple for the right DeWalt gun saves time room after room and cuts down on misfires.
The Basics: Understanding DeWalt Cable Staples
These are not standard office or upholstery staples. DeWalt cable staples are shaped to secure cable runs quickly while reducing the chance of flattening, nicking or loosely fixing the cable. Here is what matters on site.
1. The Staple Has to Suit the Cable
The crown shape and size are designed around specific cable diameters. That is what lets the staple hold the cable snugly against timber without crushing it flat.
2. Tool Compatibility Matters
A DeWalt stapler feeds and drives staples built for its magazine and firing setup. Use the right staple and you get smoother feeding, fewer jams and a cleaner finish on repeat runs.
3. Insulation Changes the Outcome
Insulated cable staples add a protective barrier between staple and cable. On the job, that means a more controlled hold and less chance of marking the sheath when you are fixing cable at pace.
What Else Do You Need for Cable Stapling Jobs?
A few sensible extras save you from jams, downtime and messy cable runs when the pace picks up.
1. Electricians Cable Staplers
This sounds obvious, but buy staples to suit the actual gun. If you are still checking model numbers on the floor, start with Electricians Cable Staplers and match the fixing properly before you order a box that will not feed.
2. Spare Staple Packs
A spare pack is a no-brainer on first fix. Running out halfway along a loft run or plot rewire means more walking, more stopping and a job that should have flown now dragging on.
3. General Staples
If the van carries more than one tacker, keep your cable fixings separate from your general Staples. It stops the usual mix-up where the wrong strip gets loaded and the gun starts jamming.
Choose the Right DeWalt Cable Staples for the Job
Match the staple to the cable type, cable size and the exact DeWalt stapler you are loading.
| Your Job | Category or Type | Key Features |
|---|---|---|
| First fix twin and earth on joists and studs | DeWalt cable staples sized for T and E | Correct crown shape, secure hold, clean drive, reduced chance of cable damage |
| Data or alarm cable runs in lofts and risers | Smaller cable staples for DeWalt stapler use | Fits lower diameter cable, keeps spacing tidy, helps avoid loose runs |
| High volume plot work | Bulk pack DeWalt electricians staples | Fewer stoppages, easier repeat loading, better for long days on one gun |
| Jobs needing added cable protection | Insulated cable staples | Protective layer around the fixing point, better for controlled grip on the sheath |
| Checking tool fit before ordering | Staples matched by compatibility | Reduces jams, misfeeds and returns caused by loading the wrong staple type |
Common Buying and Usage Mistakes
- Buying by brand alone instead of by tool compatibility is the usual mistake. Not every staple that looks close will feed properly in a DeWalt gun, so always check the listed fit first.
- Using a staple that is too tight for the cable can mark or pinch the sheath. Match the staple to the actual cable diameter, not a rough guess from memory.
- Mixing cable staples in with general fixings wastes time and causes jams. Keep cable stapler staples separate in the van and label them by tool if more than one trade uses the stock.
- Ordering one pack for a full first fix often backfires. Plot work and long runs chew through staples quickly, so buy enough to stay productive rather than stopping to reorder mid job.
- Forcing other brands into a DeWalt stapler to use up old stock is false economy. Even if they load, poor fit can mean misfires, bad seating and a rougher finish on the cable run.
Insulated vs Standard vs Mixed Compatibility Staples
Insulated Cable Staples
Best where you want a more controlled hold on the cable and less risk of marking the sheath. They suit electricians who are fixing at pace but still want a tidy, cable-safe finish.
Standard Cable Staples
A solid choice for straightforward runs where the staple is correctly sized and the tool match is spot on. They do the job well, but you still need to make sure the cable diameter is right for the fixing.
Tool Specific Compatibility Staples
These are the sensible buy if you want proper feeding and less messing about on site. When the staple is made for the exact DeWalt gun, you get fewer jams and more consistent results.
Mixed Brand Alternatives
Only worth considering if the manufacturer states clear compatibility. If not, you are gambling with feed issues, poor drive and damaged cable, which is not worth it just to save a few quid on a box.
Maintenance and Care
Keep Staples Dry
Store staple packs somewhere dry in the van or lockup. Damp packs can corrode, stick together and feed badly once they go in the magazine.
Do Not Mix Packs Loose
Keep each staple type in its own box or organiser. Mixed strips are how the wrong fixing gets loaded into the gun and turns a simple cable run into a jam clearing session.
Check for Damaged Strips
If staple strips are bent, crushed or broken, do not force them into the tool. Damaged strips usually lead to misfeeds and can mark the cable when they drive badly.
Keep the Stapler Clean
Dust and site muck inside the magazine affect how well staples feed. A quick clean of the gun and magazine saves grief, especially if the tool has been living in the bottom of the van.
Replace the Wrong Staples, Not the Tool
If the gun starts jamming or the staples are not seating right, check the staple type before blaming the tacker. A wrong or poor condition strip is often the real problem.
Why Shop for DeWalt Cable Staples at ITS?
Whether you need a single box for a small rewire or bulk dewalt cable stapler staples for repeat first fix work, we stock the range properly. That means compatible staples, related fixings and the wider Nail Gun Nails & Accessories line, all in our own warehouse and ready for next day delivery.
DeWalt Cable Staples FAQs
What cable sizes do DeWalt cable staples fit?
It depends on the exact staple type. Some are sized for twin and earth, others for smaller data, alarm or low voltage cable. Check the listed cable size range against the run you are fixing, because a staple that is too tight can mark the sheath and one that is too loose will not hold the cable neatly.
Are DeWalt cable staples insulated?
Some are, some are not. If the product is listed as insulated cable staples, that means there is a protective layer designed to help secure the cable without the staple bearing directly onto the sheath. Do not assume every DeWalt cable staple is insulated just because it is made for cable work.
Which DeWalt tools use these cable staples?
They are made for specific DeWalt cable staplers, not every tacker in the range. The safe way is to match the staple to the exact tool model shown on the product listing. If you are still choosing the gun, have a look at Electricians Cable Staplers first, then buy the staples that are listed for that tool.
Can I use other brands' cable staples in a DeWalt stapler?
Only if the compatibility is clearly stated. In real site use, mixing brands without confirmed fit is where you get jams, poor drive and staples that do not seat properly. It might look close enough in the hand, but close enough is how you waste time and risk damaging the cable.
How many cable staples come in a pack?
Pack quantities vary by staple type and application, so always check the product details before you order. If you are wiring a full plot or doing repeated runs, buy more than you think you need because cable stapling burns through packs quickly once you are moving.
Are these better than using cable clips and a hammer?
For volume work, yes. A DeWalt cable tacker with the right staples is much faster and gives more even fixing on long runs. For one or two awkward repair jobs, hand clips still have their place, but for full first fix they are slower and harder on the hands.
Will these staples work for all cable types on the van?
No. That is the trap. One staple size will not suit every cable you carry, especially if you jump between twin and earth, data and alarm cable. Match each staple to the cable diameter and the DeWalt tool you are using.
What if I need alternatives for another gun as well?
Keep the fixings separate and buy by compatibility, not by guesswork. If you run different kit across the van, compare the full Milwaukee Cable Staples range as well so each stapler gets the right strips.
