Worx SDS Drills
Worx SDS drill kits are built for drilling concrete, block and masonry when a standard drill starts labouring or burning bits out too quickly.
If you're fixing into hard block, chasing for first fix, or drilling repeated anchor holes overhead, this is where a worx sds drill earns its keep. A worx cordless sds drill gives you proper hammer action without dragging leads round the job, and the SDS Plus fitting means bits lock in securely and swap fast. If you already know the standard drill is not up to the wall in front of you, step up to a worx hammer drill sds and get on with it.
What Are Worx SDS Drills Used For?
- Drilling fixing holes into concrete, engineering brick and dense block is where a worx sds drill makes sense, especially when a combi drill starts bouncing about and barely marks the surface.
- Chasing out for electrical boxes, clips and conduit runs on first fix is quicker with a worx cordless sds drill because the hammer action does the hard work instead of your wrists.
- Installing anchors, frame fixings and support brackets in refurbs and site fit-outs is easier with an SDS Plus setup that holds the bit properly and copes better with repeated holes.
- Working overhead on ceilings or into awkward corners is less of a slog with a worx hammer drill sds, as the tool is built for masonry drilling rather than trying to force a general drill through it.
- Breaking into old mortar joints, light chiselling and stubborn masonry prep on smaller jobs can be handled by the right worx rotary hammer setup, saving you dragging larger breaking kit in for minor work.
Choosing the Right Worx SDS Drill
Match it to the wall and the volume of holes. Do not buy an SDS just because it sounds tougher than what you need.
1. SDS for masonry, combi for mixed work
If most of your day is brick, block and concrete, go with a worx sds drill. If you are mainly drilling timber, metal and occasional masonry, look at Worx Combi Drills instead because they are the better all-rounder.
2. Bare unit or full kit
If you are already on the platform, a body only worx cordless sds drill can save money. If this is your first step into the range, a worx sds drill set with battery and charger is usually the sensible way to get working straight away.
3. Drilling only or drilling and driving
If you need one tool for screws and general fixings as well, also check Worx Impact Drivers and Worx Drills and Drivers. An SDS is the right call for hard masonry, but it is not your everyday screw gun.
4. Battery capacity matters more than you think
If you are drilling a few fixings here and there, smaller batteries will do. If you are punching repeated holes in concrete all morning, keep decent capacity packs ready and check the range of Worx Batteries before you get caught short.
Who Uses These on Site?
- Sparkies use a worx sds plus drill for back box holes, clip fixings and cable route prep, especially on first fix where standard drills soon start struggling in older masonry.
- Plumbers and heating fitters reach for them when they need repeated bracket holes into block or concrete for pipe clips, trunking supports and plant room fixings.
- Kitchen fitters, joiners and shopfitters use them for frame fixings and anchor points when they are mounting into solid walls rather than timber stud.
- Maintenance teams and site managers keep a worx sds drill set handy for day to day remedial drilling jobs, snagging work and quick masonry fixes without hauling out bigger site kit.
The Basics: Understanding Worx SDS Drills
An SDS drill is not just a drill with a hammer mode. It uses a different chuck and impact system so it can hit harder into masonry and let the bit move the way it needs to.
1. SDS Plus chuck
A worx sds plus drill uses slotted shank bits that lock straight into the chuck. That means quicker bit changes and better transfer of hammer force into concrete and block.
2. Rotary hammer action
A worx rotary hammer both spins and strikes forward. On site that means cleaner progress in hard masonry, less leaning on the tool, and less chance of cooking standard masonry bits.
3. Better for repeated anchor holes
If you are drilling one light hole into soft brick, a combi might get by. If you are doing repeated fixings into concrete lintels or dense block, an SDS saves time and a fair bit of arm ache.
Worx SDS Drill Accessories That Save Time on Site
The right extras stop downtime, save wasted walks to the van, and make masonry work far less of a chore.
1. SDS Plus Drill Bits
Get the right diameters in the bag from day one. There is no point owning a worx hammer drill sds if the only bit you have is blunt, wandering, or the wrong size for the fixing.
2. Spare Batteries
A spare charged pack is common sense for repeat drilling. You do not want the drill dying halfway through bracket lines or overhead fixing work when you are up steps.
3. Charger
If you are rotating packs through the day, a proper charger keeps the kit moving. It is a lot cheaper than having lads stood about waiting for one battery to recover.
4. Dust Extraction Adaptor
For indoor refurbs and occupied properties, dust control matters. The right adaptor helps keep drilling dust down instead of leaving you sweeping up every fixing point after.
Choose the Right Worx SDS Drill for the Job
Use this quick guide to sort the right type before you buy.
| Your Job | Category or Type | Key Features |
|---|---|---|
| Occasional fixing holes in brick and block | Compact worx cordless sds drill | Good manoeuvrability, SDS Plus chuck, lighter weight for short runs of work |
| Repeated anchors into dense masonry or concrete | Worx rotary hammer | Proper hammer force, faster drilling progress, better for harder substrates |
| First fix electrical and plumbing brackets | Worx sds drill set | Battery, charger and drill together so you can get straight on with repeated fixing work |
| Mixed site work with only occasional masonry drilling | Worx combi drill | More suitable for timber, metal and screws, with hammer mode for lighter masonry jobs |
| Masonry drilling alongside screwdriving kit | Worx Cordless SDS Hammers | Dedicated drilling performance while your impact driver handles fixings and fasteners |
Common Buying and Usage Mistakes
- Buying an SDS for general drilling and screwdriving work is a common mistake. It is the right tool for masonry, but it is not the handiest option for every day joinery or second fix tasks.
- Using blunt or cheap SDS Plus bits wastes the drill's effort and slows the job right down. If progress drops off, change the bit before you start blaming the tool.
- Ignoring battery capacity catches plenty of users out. A small pack might be fine for a few holes, but repeated concrete drilling will empty it quickly, so keep a spare ready.
- Trying to force a combi drill through dense concrete instead of stepping up to a worx sds drill usually ends with burnt bits and wasted time. Match the drill to the wall and move on.
- Choosing the wrong fixing size before drilling leaves you opening holes twice or using the wrong anchor. Sort your fixing spec first, then match the SDS bit to it.
Worx SDS Drill vs Combi Drill vs Impact Driver
Worx SDS Drill
Best for concrete, block and hard masonry where you need repeated clean holes without fighting the wall. It is the one to buy when masonry drilling is the actual job, not an afterthought.
Combi Drill
Better if your work is mainly timber, metal and general fixing with just occasional holes in softer masonry. It is more versatile day to day, but it will not keep pace with an SDS in dense material.
Impact Driver
Built for driving screws, coach bolts and longer fixings quickly with less wrist twist. Pair it with an SDS if you are doing masonry drilling and fastening on the same job, because one does not replace the other.
Maintenance and Care
Keep the chuck clean
Dust and grit build up fast around an SDS chuck. Wipe it down after masonry work so bits still seat properly and do not start sticking.
Check bits before every run
A worn tip slows drilling and puts extra strain on the tool. If the bit has gone off, swap it out rather than leaning harder on the drill.
Look after the batteries
Do not leave packs rolling about in dust or sat flat for weeks. Charge them properly, store them dry, and rotate them if the drill is in regular use.
Brush off the vents
Concrete dust gets everywhere. Keeping the vents clear helps the motor stay cooler, especially after repeated drilling on tougher walls.
Replace tired bits before blaming the drill
If a worx sds drill starts feeling slower, the bit is often the real problem. Fresh bits usually sort poor drilling performance quicker than anything else.
Why Shop for Worx SDS Drills at ITS?
Whether you need a compact worx sds drill, a worx cordless sds drill kit, or dedicated Worx Cordless SDS Hammers, we stock the range trades actually buy. It is all in our own warehouse, in stock and ready for next day delivery, so you can get the right masonry drilling kit on site without hanging about.
Worx SDS Drill FAQs
Does Worx make an SDS drill?
Yes. Worx does make SDS models, including cordless options built for masonry drilling jobs where a standard drill is not enough. If you are drilling concrete, dense block or repeated fixing holes, this is the part of the Worx range you want to be looking at.
Is the Worx SDS drill suitable for concrete drilling?
Yes, that is exactly the sort of work it is for. A worx hammer drill sds is made for concrete, block and masonry, especially where a combi drill would take longer, bounce about, or burn through bits.
What SDS system does the Worx SDS drill use?
Most site users will be looking for an SDS Plus setup, and that is the common system for this type of worx sds plus drill. It takes SDS Plus shank bits that lock in fast and are widely available for normal masonry fixing sizes.
Does the Worx SDS drill come with a battery?
Some do and some do not. Body only versions are ideal if you already run Worx cordless kit, but if you are starting from scratch, check for a full worx sds drill set with battery and charger included before you order.
Can I use a Worx SDS drill for chiselling as well as drilling?
For light chipping and small masonry tidy-up jobs, yes, if the model supports that mode. It is handy for lifting loose mortar or minor breakout work, but do not expect a compact cordless SDS to replace a proper breaker.
Is a worx cordless sds drill worth it over a combi drill?
If you regularly drill into hard masonry, yes. A combi is fine for mixed work, but once you are doing repeated anchor holes in concrete or dense block, an SDS is faster, cleaner and far less hard on you and the bits.
