Vaunt Multi Tool Blade Sets
Vaunt sanding discs are for stripping back timber, keying paint, and cleaning up filler without wasting time on discs that clog or peel off mid job.
If you're on a sander all day, you want discs that stick properly, cut evenly, and do not burn out after a few passes. These vaunt orbital sanding discs and vaunt abrasive discs cover the usual site prep, snagging, and finishing work in 125mm and 150mm sizes, with hook and loop backing for quick changes. If you need matching sheets and pads, look at Vaunt Sanding Pads & Sheets, then get the right grit in the basket and crack on.
What Are Vaunt Sanding Discs Used For?
- Flattening filler on plaster repairs and joinery snagging is where vaunt sanding discs earn their keep, letting you move from rough shaping through to a paint-ready finish without swapping machines.
- Keying painted doors, skirting, and frames before recoating is quicker with vaunt orbital sanding discs, especially when you need an even scratch pattern that does not gouge the surface.
- Cleaning up timber edges, sheet material, and cut faces on first and second fix jobs is easier with vaunt abrasive discs, giving you fast stock removal without the faff of hand sanding every piece.
- Stripping back tired finishes on site fit-outs and refurb work suits vaunt 125mm sanding discs and vaunt 150mm sanding discs, depending on whether you need tighter control or more coverage.
- Working through mixed prep jobs from the same van is simpler when you keep a vaunt sanding disc set in a few common grits, so you are not stuck trying to finish with a disc that is too coarse or too spent.
Choosing the Right Vaunt Sanding Discs
Sorting the right disc is simple: match the size and grit to the job, not just to what is lying in the van.
1. Pick the Right Size First
If your sander takes 125mm discs, stick with 125mm and do not try making other sizes fit. Vaunt 125mm sanding discs suit general site sanding and tighter work, while 150mm discs cover more area faster on bigger panels and broad prep work.
2. Match the Grit to the Stage of the Job
If you are stripping back old finish or knocking filler flat, start coarse. If you are keying up between coats or finishing timber before paint, go finer. Using too coarse a grit too late just leaves scratches for you to sort out afterwards.
3. Hook and Loop Makes Life Easier
For stop start site work, vaunt hook and loop sanding discs are the sensible choice. If you are changing grits through the day, they save time and keep the disc seated properly, as long as your backing pad is still in decent nick.
4. Buy a Set if You Handle Mixed Prep
If your work jumps between filler, paint prep, bare timber, and final finish, a vaunt sanding disc set makes more sense than buying one grit in bulk. You will use the right disc for each pass instead of trying to force one worn disc through the whole job.
Who Uses These on Site?
- Decorators reach for vaunt sanding discs when they are flattening filler, keying gloss, and prepping walls and woodwork for a decent finish that does not show every mark under fresh paint.
- Chippies use vaunt orbital sanding discs for easing edges, cleaning up cut lines, and sorting first fix and second fix timber before it goes in front of the client.
- Kitchen fitters and shopfitters keep vaunt abrasive discs in the van for trimming back fillers, cleaning panel edges, and getting units and scribes looking right before handover.
- Maintenance teams like vaunt hook and loop sanding discs because they swap over quickly when a small repair turns into three different surfaces and a couple of grit changes.
Sanding Extras That Keep the Job Moving
A few simple add-ons save wasted discs, poor finish, and extra clean-up at the end of the day.
1. Backing Pads
If your discs keep lifting, wobbling, or wearing unevenly, the backing pad is usually the culprit. Swap the pad before you blame the abrasives, otherwise you will keep chewing through discs and wondering why the finish looks rough.
2. Sanding Rolls
For edges, awkward touch-ins, and quick hand prep where the orbital will not reach, keep Vaunt Sanding Rolls nearby. They save dragging out more kit just to sort a small patch.
3. Multi Tool Sanding Attachments
Corners, reveals, and tight spots always catch you out. Vaunt Multi Tool Sanding Attachments let you get into places a round disc simply cannot reach.
4. Dust Extraction and Spare Abrasives
Clean extraction helps discs cut better and clog less, especially on filler and paint prep. It is also worth keeping spare sheets from Vaunt Sanding Pads & Sheets so you are covered when the sander is the wrong tool for the surface.
Choose the Right Vaunt Sanding Discs for the Job
Use this quick guide to match disc type and grit choice to the work in front of you.
| Your Job | Disc Type | Key Features |
|---|---|---|
| Flattening filler and heavy prep | Coarse Vaunt sanding discs | Fast stock removal, suits first passes, good for knocking high spots down quickly |
| Keying paint and varnish before recoating | Medium grit vaunt orbital sanding discs | Even scratch pattern, less risk of gouging, quick disc changes with hook and loop |
| Finishing timber and final prep | Fine vaunt abrasive discs | Smoother finish, lighter cut, better for visible surfaces before paint or stain |
| General van stock for mixed jobs | Vaunt sanding disc set | Range of grits, covers prep to finish, saves getting caught short on site |
| Larger panels and broad surface sanding | Vaunt 150mm sanding discs | More coverage per pass, better for bigger boards, cuts time on wide open areas |
Common Buying and Usage Mistakes
- Buying the wrong disc diameter is the first mistake. If the disc does not match the pad properly, it will not run right, dust pick-up suffers, and you risk poor finish or wasted abrasives.
- Using one grit for the whole job just wastes time. Start too fine and you will be there all day. Stay too coarse and you will leave scratches that show through paint or topcoat.
- Blaming the disc when the backing pad is worn is common. If hook and loop grip is tired, discs lift and chatter, so replace the pad before burning through another pack.
- Letting the sander do no dust extraction work is a false economy. Packed dust clogs the abrasive, slows the cut, and shortens disc life, especially on filler and old coatings.
- Pressing too hard to make a worn disc cut again usually ruins the finish. Swap the disc once it stops biting cleanly rather than forcing it and creating more remedial sanding.
125mm vs 150mm vs Sanding Disc Sets
125mm Sanding Discs
These are the usual pick for general site work, snagging, and smaller sanders. They give you better control on edges, trim, filler patches, and tighter bits of joinery where a bigger disc can feel clumsy.
150mm Sanding Discs
Go 150mm when you are covering larger panels, doors, boards, or broad prep areas. They remove material over a wider pass and can speed up bigger jobs, but only if your machine is built for that size.
Sanding Disc Sets
A set is the sensible option if your day includes rough prep, intermediate sanding, and final finish. You get a spread of grits ready to go, which is far more practical than trying to make one grade cover every stage.
Maintenance and Care
Keep Them Dry and Flat
Store discs somewhere dry in the van or workshop. If they get damp, curled, or filthy, they will not sit right on the pad and the cut will be inconsistent from the start.
Clean the Backing Pad
Dust and fluff build up in the hook and loop face over time. Brush it out regularly so the disc grips properly and does not start peeling off halfway through the pass.
Change Worn Discs Early
Once a disc is glazed, clogged, or torn, bin it. Hanging on to it too long slows the job down and usually leaves a poorer finish that needs more work afterwards.
Check Extraction Holes Line Up
Make sure the disc sits properly on the pad so dust holes are not blocked. Good extraction keeps the abrasive cutting cleaner and helps stop filler and paint dust from clogging the face.
Why Shop for Vaunt Sanding Discs at ITS?
Whether you need vaunt 125mm sanding discs, vaunt 150mm sanding discs, or a vaunt sanding disc set for mixed prep work, we stock the range properly. You will also find the wider Vaunt line, plus related finishing gear like Vaunt Surforms & Blades. It is all held in our own warehouse, in stock, and ready for next day delivery.
Vaunt Sanding Discs FAQs
What sanding discs does Vaunt make?
Vaunt makes sanding discs for orbital sanding and general abrasive prep work, including options suited to timber, filler, painted surfaces, and routine site finishing. The range is built around the sizes and grit choices trades actually use, rather than odd formats that are hard to replace.
What sizes are Vaunt sanding discs available in?
Vaunt sanding discs are commonly available in 125mm and 150mm sizes. Check your sander pad before ordering, because getting the diameter wrong means poor fit, poor dust pick-up, and a finish that is harder to keep even.
Are Vaunt sanding discs hook and loop or adhesive backed?
Vaunt sanding discs are hook and loop, which is what most site users want for random orbital sanders. They are quicker to change, easier to swap between grits mid job, and less hassle than older adhesive styles.
What grit range is available in Vaunt sanding discs?
Vaunt sanding discs are available across the usual grit spread for prep and finishing, from coarser grades for stripping and flattening through to finer grades for final sanding. Best practice is simple: coarse for removal, medium for keying, fine for finishing.
Are these any good for filler, or do they clog straight away?
Yes, they are well suited to filler work if you use the right grit and decent extraction. Like any abrasive, they will clog if you lean on too hard or keep going once the disc is spent, but in normal use they hold up properly for snagging and prep.
Will these fit any orbital sander?
Not every one, no. You need to match the disc diameter to the machine and make sure the hook and loop setup suits your backing pad. The safe move is to check whether your sander takes 125mm or 150mm discs before you buy.
