OX Tools More Hand Tools
OX more hand tools cover the awkward jobs standard kit misses, from scraping and stapling to carrying bricks and stripping cable on site.
When the usual hammer, level and knife will not finish the job, this is the kit you reach for. These ox more hand tools are built for snagging, prep, first fix and material handling, with practical designs that stand up to rough site use. If you need ox specialist hand tools that earn space in the van, start here.
What Are OX More Hand Tools Used For?
- Scraping old adhesive, paint, silicone and site muck off floors, frames and boards is where these tools save time, especially on refurbs where surfaces need cleaning back properly before the next trade gets in.
- Stapling membranes, insulation, sheeting and light fixings in place is quicker with the right staple gun, particularly on roofing jobs, timber work and temporary protection around finished areas.
- Carrying bricks, blocks and other awkward loads across site is easier with proper load carrying tools, giving brickies and labourers a safer grip and less strain over a full day of shifting materials.
- Stripping and crimping cable cleanly matters on first fix and board work, and the right hand tools help sparks avoid nicked conductors, loose terminations and wasted time redoing connections.
- Handling the fiddly jobs that slow a day down is exactly where ox specialist hand tools come into their own, whether you are on prep work, final snagging or keeping the van stocked for odd site problems.
Choosing the Right OX More Hand Tools
Sorting the right one is simple: match the tool to the job you actually do, not the one you might do once a year.
1. Site Prep or First Fix
If you are mostly cleaning back surfaces, lifting residue or stripping old material, go for scrapers and blades that are easy to control and simple to reblade. If your day is more electrical first fix, strippers and crimpers will save you more time than any general purpose hand tool.
2. Repetitive Carrying Jobs
If you are shifting bricks or blocks all day, do not make do with gloves and guesswork. Proper load carrying tools are worth it because they reduce hand strain and give you a more secure hold when the ground is wet or uneven.
3. Trade Range or Pro Range
If the tool is for occasional van use or backup, OX Trade will usually do the job. If it is something you will use day in, day out on busy sites, OX Pro is the better shout for tougher build and longer service.
4. Keep the Fiddly Jobs Covered
This category is about filling the gaps in your kit. If a task keeps cropping up and slowing the day down, buy the proper tool for it once and keep it in the van rather than bodging through with the wrong bit of kit.
Who Uses These on Site?
- Brickies and labourers keep brick carriers and other load carrying tools close by for moving bricks and blocks from stack to work area without fighting for grip every trip.
- Sparks reach for strippers and crimpers during first fix, board terminations and repair work, because a clean strip and solid crimp saves faults later on.
- Roofers, chippies and general builders use staple guns for breather membrane, felt, insulation and temporary sheet fixing, especially where speed matters more than messing about with pins.
- Decorators, fitters and snagging teams rely on scrapers for lifting old sealant, paint and residue off finished surfaces, and most will keep one in the bag because it gets borrowed all the time.
- Maintenance teams and site managers often carry this sort of OX hand tools kit because it covers the odd jobs that stop progress when no one has the right tool to hand.
Useful Extras to Keep These Tools Working
A few sensible extras stop small jobs turning into wasted trips back to the van.
1. Replacement Blades
If you are using scrapers on sealant, paint or stubborn adhesive, spare blades are a must. A blunt edge just chews at the surface, slows you down and makes a tidy job harder than it needs to be.
2. Staples
The right staples matter more than most lads think. Wrong size or wrong type means poor hold, jams and wasted time, so stock what suits your staple gun and the material you fix most often.
3. Crimps and Connectors
Strippers and crimpers are only half the job. Keep the correct terminals and connectors with them so you are not left with the tool but nothing to finish the connection properly.
Choose the Right OX More Hand Tools for the Job
Use this quick guide to sort the right tool for the work in front of you.
| Your Job | Category or Type | Key Features |
|---|---|---|
| Removing old sealant, paint or adhesive during prep | Scrapers | Replaceable blades, solid grip, good control on flat surfaces and awkward edges |
| Fixing membrane, felt or insulation quickly | Staple Guns | Fast repeat fixing, easy loading, dependable firing and decent access in tight spots |
| Moving bricks or blocks across site | Brick Carriers | Secure grip, better balance, reduced hand strain and safer handling on repetitive lifts |
| Stripping cable and making neat terminations | Strippers and Crimpers | Clean stripping, proper crimping action and sizing that matches the cable and terminals |
| Covering odd snagging and specialist site tasks | Specialist Hand Tools | Task specific designs, van friendly sizing and proper solutions for awkward jobs |
Common Buying and Usage Mistakes
- Buying general hand tools and expecting them to cover specialist jobs usually ends in slower work and rougher results. If you scrape, staple, crimp or carry materials regularly, buy the tool made for it.
- Choosing the cheapest scraper or staple gun for daily use can cost more in the long run because blades slip, staples jam and grips give up. For repeat site use, spend on the range that matches the abuse.
- Using worn scraper blades or damaged crimping jaws ruins the finish and can damage the material. Replace consumable parts early instead of forcing another day out of them.
- Ignoring compatibility with staples, crimps or cable sizes is a common one. Check what the tool takes first, otherwise you end up with fixings or connectors that do not fit or hold properly.
- Treating load carrying tools like lifting gear for anything and everything is asking for trouble. Use brick carriers for the loads they are designed for and do not overload them just to save a trip.
Scrapers vs Staple Guns vs Strippers and Crimpers
Scrapers
Best for prep, clean-up and snagging jobs where you need to remove old material without making a bigger mess. They are simple, quick and effective, but only if the blade is right for the surface and kept sharp.
Staple Guns
Best where speed matters and the fixing does not need screws or nails. They are ideal for sheeting, felt and membrane work, but they are only as good as the staples you feed them and the material underneath.
Strippers and Crimpers
Best for electrical work where clean cable prep and solid terminations matter. They are not just pliers with extra steps. Use the proper tool here or you risk damaged conductors and poor connections.
Load Carrying Tools
Best for repetitive handling of bricks and similar materials where grip and control make the difference over a full shift. They will not replace proper lifting kit, but they do make day to day carrying safer and less tiring.
Maintenance and Care
Clean After Dirty Work
Wipe off adhesive, paint, dust and site grime after use, especially on scrapers and crimpers. Letting muck build up affects grip, moving parts and cutting accuracy.
Change Blades Before They Fight You
A scraper blade that drags or skips is done. Change it before it starts marking surfaces or forcing you to lean too hard into the job.
Keep Moving Parts Dry and Free
Staple guns and crimpers need moving parts to stay clean and dry. If they have been left in the van wet, dry them off and check for rust before the next shift.
Store Them Properly
Do not just throw specialist tools loose under a pile of gear. Keep them in a pouch, box or drawer so edges stay usable and handles do not get cracked by heavier kit.
Repair or Replace Sensibly
If a handle is loose, jaws are worn or a staple gun keeps jamming, sort it early. Consumables are worth replacing, but once the core tool starts costing time on site, swap it out.
Why Shop for OX More Hand Tools at ITS?
Whether you need scrapers, staple guns, brick carriers, strippers, crimpers or other specialist site kit, we stock the full OX range in one place. You will also find OX hand tools for the rest of your setup, plus OX cutting tools when the job needs blades and cutters as well. It is all held in our own warehouse, in stock and ready for next day delivery.
OX More Hand Tools FAQs
What other hand tools does OX make?
Quite a lot beyond the standard hammers and levels. In this part of the range you will find things like scrapers, staple guns, brick carriers, strippers, crimpers and other task specific gear that covers the awkward jobs general tools do badly. If you are after prep kit, have a look at OX scrapers and blades. For fixing membranes and sheet materials, there are OX staple guns. For electrical first fix and tidy terminations, there are OX strippers and crimpers.
Are OX hand tools any good?
Yes, they are well regarded on site because they are built around actual trade use rather than shelf appeal. The better answer is this: they are honest working tools. OX Trade covers everyday use well, while OX Pro is the range most lads step up to when the tool gets hammered every day.
What is a brick carrier used for?
A brick carrier is used for lifting and carrying bricks or similar materials with a more secure grip. It makes repetitive trips across site easier on the hands and gives better control than trying to clutch loose bricks, especially when conditions are muddy or you are moving stock over distance.
What is the difference between OX Trade and OX Pro?
OX Trade is the more budget conscious working range and suits lighter use, backup kit or lads just getting stocked up. OX Pro is aimed at heavier day to day trade use, usually with tougher materials, better ergonomics and longer life where the tool sees proper site abuse.
Where are OX hand tools made?
OX hand tools are a global product range, so manufacturing can vary by product type. The important bit for most trades is not the postcode on the box but whether the tool stands up to the work. OX tools are designed for trade use, and the ranges are built around site durability and practical handling.
Are these specialist hand tools worth keeping in the van?
Yes, if they solve jobs you hit regularly. This is the sort of kit that saves you when a standard hand tool will do the job badly or too slowly. A decent scraper, staple gun or crimper usually earns its keep fast because it stops bodges and repeat work.
