Makita Staples
Makita staples are the right fix when you need clean, repeat fastening into sheet, membrane, trim and fencing without stoppages or bent legs.
If you're loading a stapler for breather membrane, insulation layers, light trim or repetitive fixing work, get the staple shape and length right first. These makita stapler staples and makita narrow crown staples are made to feed properly, hold fast and save wasted strips on site. If you're already running Makita Tools, this is the place to sort the right sizes and finishes before the job starts.
What Are Makita Staples Used For?
- Fixing breather membrane, vapour barriers and sheet materials where you need fast, repeat shots that sit flat without tearing the material to bits.
- Securing insulation facings, light timber trims and backing materials during first fix when a hammer tacker or nail would be slower and rougher.
- Handling upholstery, lining and finer bench work with shorter makita staples where a neat hold matters more than brute force.
- Fastening wire mesh, fencing fabric or outdoor materials with longer or galvanised staples where weather resistance and proper bite into timber both matter.
- Keeping service jobs moving when you need a fresh makita staple pack in the van so the stapler is not sat idle halfway through a run of repetitive fixings.
Choosing the Right Makita Staples
Sorting the right staple is simple: match the crown, leg length and finish to the material, not just the stapler.
1. Pick the Leg Length for the Material Stack
If you're pinning thin membrane or fabric, short legs like makita staples 10mm usually do the job without punching through or leaving proud marks. If you're fixing thicker layers or biting deeper into timber, step up to longer options like makita staples 25mm so the hold is there first time.
2. Narrow Crown for Cleaner, Tighter Fixing
If the work needs a tidy finish or you're fixing thinner materials, makita narrow crown staples are the safer bet. They spread the hold neatly and tend to suit trim, sheet backing and internal detail work better than rougher, broader fixing options.
3. Galvanised Matters Outdoors
For fencing, sheds, external membranes or anything seeing damp, use makita galvanised staples. Plain indoor staples can stain, corrode and let go early once the weather gets at them.
4. Check Stapler Compatibility Before You Load Up
Do not guess on crown width or gauge. If the stapler is built for a specific strip type, buy to that spec or you will get jams, misfires and wasted packs. A few minutes checking beats stripping a jammed gun on a scaffold board.
Who Uses These on Site?
- Roofers and timber frame crews use makita narrow crown staples for membranes, felt and sheet layers because they go in quickly and hold cleanly without slowing the run down.
- Joiners and chippies reach for makita stapler staples when fixing thin trims, back panels and light sheet goods where a nail can split the edge or leave a rougher finish.
- Fencing teams and landscapers use longer or galvanised staples for netting, wire and outdoor timber jobs where the fixing needs to put up with weather and movement.
- Upholsterers and fit-out teams keep shorter sizes close by for fabrics, linings and neat internal work where the wrong leg length will show through or damage the face.
Stapling Essentials That Keep the Job Moving
A few sensible extras save jams, downtime and that walk back to the van when the stapler runs dry.
1. Spare Staple Packs
Sounds obvious, but this is the one people forget. Keep an extra makita staple pack in the van or tool bag so you are not stopping a membrane run or fencing line because the last strip is gone.
2. Stapler Carry Case or Storage Box
Loose strips get bent, damp and full of site dust. Proper storage keeps makita staples straight and dry, which means better feeding and fewer mid-job jams.
3. Stapler Maintenance Oil and Cleaning Gear
If your stapler is seeing heavy use, a quick clean-out and the right maintenance stops misfires and poor driving depth. Better that than blaming good staples for a dirty magazine.
Choose the Right Makita Staples for the Job
Use this as a quick guide before you load the gun.
| Your Job | Staple Type | Key Features |
|---|---|---|
| Fixing membrane, vapour barrier or thin sheet | Makita narrow crown staples in shorter lengths | Clean seating, less chance of tearing, fast repeat fixing |
| Light trim, backing boards and joinery detail | Makita stapler staples sized to suit the material | Neater hold, reduced splitting risk, better control on thinner stock |
| Upholstery, linings and finer internal work | Makita staples 10mm or similar short leg options | Shorter penetration, tidy finish, less risk of showing through |
| Fencing, wire fixing and outdoor timber jobs | Makita galvanised staples in longer lengths | Weather resistance, stronger bite, better holding power outside |
| Thicker layered materials or deeper timber bite | Makita staples 25mm | Longer leg for deeper anchoring and a more secure hold |
Common Buying and Usage Mistakes
- Buying by length only and ignoring crown width or gauge is a classic mistake. If the strip profile does not match the stapler, expect jams, poor feeding and a lot of swearing.
- Using short staples for thicker material stacks saves nothing. They may fire in, but the hold will be weak and the fixing can pull free once the material is under tension.
- Using indoor staples outside is asking for trouble. If the job is exposed to damp or weather, switch to galvanised staples or the fixing can corrode early and stain the work.
- Forcing one staple type across upholstery, trim and fencing never ends well. Fine work needs shorter, tidier staples, while rough external jobs need more bite and tougher finish.
- Leaving staple strips loose in the van bends them and fills them with dust. Store them properly or you can turn a decent stapler into a jam machine.
Narrow Crown Staples vs Galvanised Staples vs Longer Staples
Makita Narrow Crown Staples
Best where you want a neat, controlled fixing into membrane, trim or thinner sheet materials. They are the sensible choice for clean internal work, but they are only right if the stapler is built for that crown and gauge.
Makita Galvanised Staples
These are the safer call for outside jobs, damp conditions and fencing work. They cost more than plain staples, but they hold up better against weather and save premature rusting.
Shorter Staples
Short legs suit upholstery, linings and thin materials where you do not want blow-through or witness marks. They are cleaner on delicate work, but they will not give enough bite for thicker timber-based fixing jobs.
Longer Staples
Longer options are for thicker layers, tougher fixing and outdoor work where proper penetration matters. Use them where you need holding power, but do not overdo it on fine materials or you risk damage and visible legs.
Maintenance and Care
Keep Packs Dry
Staples hate damp storage. Keep boxed strips sealed and off the van floor so they do not pick up moisture, surface corrosion or soft packaging that falls apart in the tool bag.
Store Strips Flat and Straight
Bent strips are one of the quickest ways to jam a stapler. Keep packs flat in a case or organiser rather than loose under other kit.
Clean the Stapler Magazine
Dust, adhesive residue and site muck in the magazine can make good staples feed badly. Wipe it out regularly, especially after dusty loft, roofing or fencing work.
Replace Damaged Strips
If a strip is crushed, rusty or breaking apart, bin it. Trying to use damaged staples usually ends with misfires, bent legs and more downtime than the pack is worth.
Match Finish to the Environment
For outdoor use, start with galvanised staples instead of hoping plain ones will last. Choosing the right finish from day one is better than repairing failed fixings later.
Why Shop for Makita Staples at ITS?
Whether you need a short strip for trim work, makita staples 25mm for deeper bite, or galvanised options for outside jobs, we stock the proper range in one place. You can also sort the rest of your fastening kit with Makita Fixings & Fasteners, plus Makita Screws, Makita Screwdriver Sets and Makita Phillips Screwdrivers. It is all held in our own warehouse, in stock and ready for next day delivery.
Makita Staples FAQs
What staple sizes does Makita make?
Makita staples are available in a spread of lengths to suit different jobs, including common site sizes such as 10mm and 25mm. The key thing is not just length, though. Check the crown width and gauge your stapler is designed for, because the wrong strip profile will cause jams even if the leg length looks right.
Are Makita staples compatible with other brands' staplers?
Sometimes, but do not assume they are. Stapler compatibility comes down to crown width, gauge, leg length range and how the magazine is set up. If another brand uses the exact same staple spec, they may feed fine. If not, expect misfires or jams. Always check the stapler manual before buying in bulk.
Which staples should I use for upholstery versus fencing?
For upholstery and finer internal work, go shorter and neater so you do not mark the face or punch through the material. For fencing, wire and outdoor timber jobs, use longer staples with enough bite to hold properly, and pick galvanised if the fixing will be exposed to weather.
How many staples come in a Makita pack?
Pack quantities vary by staple type and size, so check the listing before ordering. If you are doing repetitive work like membrane runs or fencing, it is worth buying enough packs to finish the job in one go rather than hoping one box will stretch further than it will.
Are Makita staples galvanised for outdoor use?
Some Makita staples are galvanised, and those are the ones to use where damp, weather or treated timber are part of the job. Not every staple in the range will be galvanised, so check the finish in the product details rather than guessing from the photo.
Will these staples hold in treated timber and rough outdoor jobs?
Yes, if you pick the right length and finish. For rough external work, the staple needs enough leg length to bite properly, and galvanised finish is the safer option. Too short and it will pull out. Wrong finish and it can corrode before the job has properly aged.
