MAFELL COMBI DRILLS
Mafell combi drill kits are built for accurate drilling, driving and hammer work where cheap gear slips, stalls or wanders under load.
If you're fitting all day and swapping between timber, fixings and the odd masonry hole, this is the sort of kit that earns its keep. A Mafell cordless combi drill gives you clean control, proper torque and the CAS battery platform, so you're not juggling chargers just to keep moving. If you already run Mafell Tools or need to compare the wider Mafell Drills and Drivers range, start here and pick the drill that matches your workload.
What Are Mafell Combi Drills Used For?
- Drilling clean holes in timber, sheet material and joinery components is where a Mafell combi drill pays off, especially when you're doing accurate fit-out work and cannot afford bit wander.
- Driving long screws into studwork, carcassing and site-made frames is easier with a Mafell drill driver because the torque is there without the tool feeling clumsy in hand.
- Switching to hammer mode for plugging into brick or block saves carrying a second tool for small fixing jobs, snagging work and day-to-day installation tasks.
- Working through first fix and second fix on one battery platform suits trades already running CAS kit, so a Mafell cordless combi drill slots straight into the van without extra charging faff.
- Using the right accessories matters on cleaner, repeat work, and matched Mafell Drill Bits help keep holes true and fixings seated properly.
Choosing the Right Mafell Combi Drill
Sorting the right one is simple: match the drill to the work you actually do, not the spec sheet you think sounds impressive.
1. Combi Drill or Drill Driver
If you're mainly drilling timber, fitting ironmongery and driving fixings all day, a Mafell drill driver may be all you need. If your week includes plugging into brick or block, go straight for a Mafell combi drill with hammer function and save carrying another tool.
2. Body Only or Full Kit
If you already run CAS batteries, a Mafell drill body only makes sense and keeps cost down. If this is your first step into the platform, buy the full kit so you're not stuck with a tool and no power on day one.
3. Torque and Control
If you're running big fixings into timber frames or repetitive install work, look for the model with the stronger torque figures and proper clutch control. For lighter second fix and cabinet work, balance and feel matter just as much as outright power.
4. Chuck and Accessory Fit
Do not ignore chuck size just because most jobs use standard bits. If you're stepping up to larger drilling or specialist boring, make sure the chuck takes what you use day in, day out, including matched Mafell Dowel Drill Bits where precision joinery work demands it.
Who Uses These on Site?
- Joiners and chippies rate a Mafell 18v combi drill for first fix, kitchen fitting and detailed install work, where a drill has to drive hard but still stay accurate on hinges, carcasses and fixings.
- Sparkies use a Mafell hammer drill for back boxes, clips and general fixing into block or brick when they want one drill to cover cable runs, tray work and quick masonry holes.
- Kitchen fitters and shopfitters go for a Mafell drill driver because it gives better control on visible worktops, cabinets and hardware where chewed heads and sloppy drilling look amateur.
- Maintenance teams and site fitters keep a Mafell cordless combi drill on hand for mixed jobs across timber, metal fixings and light masonry, especially when they need one dependable tool rather than three compromises.
The Basics: Understanding Mafell Combi Drills
A combi drill covers three core jobs in one tool. The useful bit is knowing when to use each mode so you drill cleaner, drive faster and stop wrecking fixings.
1. Drill Mode
This is for clean drilling in timber, metal and sheet material. Use it when accuracy matters, such as pilot holes, hardware fitting and general boring where you want the bit to cut properly without the hammer action chewing the edge.
2. Drive Mode and Clutch Settings
This is what stops you burying screws too deep or snapping heads. Set the clutch to suit the fixing and material, and the drill driver will shut the power down before you damage the work or your wrist.
3. Hammer Mode
This adds a knocking action for lighter masonry drilling into brick and block. It is ideal for plugs and general fixings, but for long runs in hard concrete you still want an SDS drill rather than asking a combi to do the wrong job.
Accessories That Keep Your Mafell Combi Drill Working
The right extras save wasted trips to the van and help the drill do cleaner, more accurate work.
1. Spare CAS Batteries
A spare battery is the obvious one, but it matters more on install days than people admit. You do not want the drill dying halfway through fixings when you're up steps or working room to room trying to keep momentum.
2. Drill Bit Sets
Keep proper wood, metal and masonry bits with the drill so you're not forcing one tired bit through everything. A fresh set of Mafell Drill Bits makes a noticeable difference to hole quality and reduces slipping in the chuck.
3. Dowel Drill Bits
If your work leans toward furniture, joinery or accurate timber assembly, dedicated Mafell Dowel Drill Bits save you fighting for repeatable depth and alignment with general purpose bits.
4. Tool Bags and Totes
A proper carry setup stops the drill, charger, batteries and bits ending up loose in the van. Mafell Tool Bags & Totes are worth it if you want the kit together, protected and ready to grab for smaller jobs.
Choose the Right Mafell Combi Drill for the Job
Use this quick guide to sort the right setup without overbuying.
| Your Job | Mafell Category or Type | Key Features |
|---|---|---|
| Kitchen fitting, cabinets and second fix joinery | Mafell drill driver | Good clutch control, balanced feel, clean drilling and precise screwdriving. |
| General site install with timber, fixings and some plugging | Mafell cordless combi drill | Three modes in one tool, hammer function, solid torque and fewer tool changes. |
| Daily first fix and heavier screwdriving | Mafell 18v combi drill kit | Stronger runtime, batteries included, charger included and ready for full shifts. |
| Adding to an existing CAS setup | Mafell drill body only | No duplicate batteries, lower upfront cost and ideal if you already run CAS packs. |
| Light masonry fixing into brick or block | Mafell hammer drill combi | Hammer mode for plugs and anchors without carrying a separate drill for small jobs. |
Common Buying and Usage Mistakes
- Buying a combi drill for constant concrete drilling is the wrong call. It will do light masonry holes, but if most of your work is hard concrete, get an SDS and stop punishing the wrong tool.
- Choosing body only without checking your battery platform catches people out. If you do not already run CAS batteries and charger, that cheaper bare unit quickly stops looking cheap.
- Ignoring chuck capacity limits what bits you can use. Check the chuck size before ordering if your work includes larger diameter drilling or specialist boring bits.
- Running worn or cheap bits in a premium drill wastes the benefit of the tool. Poor bits wander, burn and slip, so replace them before blaming the drill for rough results.
- Leaving the clutch too high for small fixings ruins heads and damages finished work. Back it off for hardware, cabinet screws and visible joinery where control matters more than brute force.
Combi Drill vs Drill Driver vs SDS Drill
Mafell Combi Drill
This is the best all-rounder if your week jumps between drilling timber, driving fixings and making the odd masonry hole. It covers most install work well, but it is still not the right choice for sustained heavy concrete drilling.
Mafell Drill Driver
Pick this if your work is mainly joinery, fitting and screwdriving where control matters more than hammer action. It is often the cleaner choice for workshop and finish work, but it will not help when you need to plug brick or block.
SDS Drill
An SDS is the right tool for repeated masonry and concrete work, especially larger holes or harder material. It hits far harder than a combi, but it is bulkier and overkill for everyday drilling and driving tasks.
Maintenance and Care
Keep the Chuck Clean
Dust and fine swarf build up fast around the jaws. Brush it out regularly so bits seat properly and the chuck keeps holding tight under load.
Wipe Down After Masonry Work
Brick and block dust gets everywhere and it is abrasive. A quick wipe-down after hammer drilling helps protect vents, controls and moving parts from needless wear.
Look After the Batteries
Do not leave packs flat in a cold van for weeks. Charge them properly, rotate them through use and store them dry if you want decent runtime and a longer working life.
Check Bits Before Blaming the Drill
If holes are rough or the tool feels like it is struggling, inspect the bit first. Blunt, bent or cheap accessories make any drill work harder and give worse results.
Store It as a Full Kit
Keep the drill, charger, batteries and core bits together in one bag or case. That stops knocks in transit and saves time when you need the tool for a quick call-out or snagging job.
Why Shop for Mafell Combi Drills at ITS?
Whether you need a Mafell combi drill, a Mafell drill driver, a Mafell cordless combi drill kit or a Mafell drill body only, we stock the proper range for trade use. It is all held in our own warehouse, ready for next day delivery, so you can get the right drill on site without hanging about.
Mafell Combi Drill FAQs
Does the Mafell combi drill use CAS batteries?
Yes. The Mafell combi drill range uses the CAS battery system, which is handy if you already run compatible cordless kit and do not want another charger cluttering the van. Just check the listing if you are buying body only, so you know exactly what is included.
How does the Mafell combi drill compare to Festool or Metabo?
Mafell sits firmly in the premium end and is usually chosen by trades who care about accuracy, feel and long-term reliability rather than just headline numbers. Against Festool or Metabo, it is a serious site and fit-out tool with excellent control, but the right choice still comes down to the jobs you do and whether you are already bought into CAS.
Is the Mafell combi drill available body only?
Yes, selected models are available as Mafell drill body only options. That makes sense if you already own CAS batteries and charger, but if you are starting from scratch, a full kit is usually the better buy so you can use it straight away.
What chuck size does the Mafell combi drill have?
Chuck size varies by model, so check the product spec before ordering if you use larger bits or specialist accessories. For most site drilling and driving jobs, the standard keyless chuck setup covers common wood, metal and masonry bits without issue.
Does the Mafell combi drill have a hammer function?
Yes, a Mafell combi drill includes a hammer mode for lighter masonry drilling into brick and block. It is spot on for plugs and general fixings, but if you are drilling hard concrete all day, use an SDS instead of forcing a combi to do the wrong job.
