Bosch Laser Targets & Staff Poles
Struggling to pick out your reference line? A Bosch laser target gives you a clear surface for lining up and checking levels.
For groundworkers and fitters, a Bosch laser staff carries height readings while a compatible pole supports the instrument. Choose the target, staff or mounting support that matches your laser and setting-out work.
What Are Bosch Laser Targets, Staffs and Poles Used For?
- Check cabinet and ceiling reference lines against a Bosch laser target plate when the beam is difficult to distinguish on the work surface.
- Transfer excavation and drainage heights using a compatible detector mounted on a Bosch laser staff, keeping the staff upright at each measuring point.
- Read height differences across foundations or paved areas with a graduated Bosch measuring staff and a suitable optical level.
- Position a compatible line laser at working height on a Bosch laser pole when setting out partitions or tiling inside a room.
Choosing the Right Bosch Laser Target, Staff or Pole
Buy for the measurement you need: a target shows the beam, a staff provides a height reference, and a pole supports the instrument.
1. Match the Target to the Beam
If you need a Bosch laser target plate, check its suitability for your laser colour. Do not expect a passive target to replace a detector when sunlight makes the beam difficult to see.
2. Check Staff Graduations and Clamps
For optical readings, choose a staff with suitable graduations. For detector work, check that the receiver clamp fits the staff profile and that its usable length covers the height differences on your job.
3. Check Pole Height and Mounting Compatibility
For an indoor mounting pole, check the supported room height, instrument thread and bracket requirements. If there is no sound overhead surface for a pressure-fit pole, use an appropriate freestanding support instead.
Who Uses Bosch Laser Targets and Staffs?
Groundworkers use staffs to check formation levels and drainage falls without moving the instrument for every reading. Ceiling fixers, kitchen fitters and tilers use target plates to check reference lines, while an indoor mounting pole lets them adjust laser height as the work progresses. Match these accessories to your Bosch Laser Levels rather than assuming every fitting is interchangeable.
The Basics: Understanding Laser Targets, Staffs and Poles
These accessories do different jobs. Choosing the wrong one will not solve a visibility problem or give you a usable height reading.
1. Targets Give the Beam a Reference Surface
A target plate provides a marked surface against which you can locate a laser line or spot. It does not electronically detect the beam or increase the laser's rated range.
2. Staffs Carry the Height Reference
A staff stands on the point being checked. With Bosch Optical Levels, you read its graduations through the telescope. With suitable Bosch Rotary Lasers, a compatible receiver locates the laser plane along the staff.
3. Mounting Poles Hold the Laser
An indoor mounting pole supports the instrument at an adjustable height. It is not a measuring staff, and movement in its mounting surfaces can shift your reference line.
Accessories for Reliable Height Checks
Match the receiver and instrument support before heading out to set levels.
1. Compatible Laser Detector and Staff Clamp
In bright conditions, a target plate alone may not make the beam visible. Choose suitable Bosch Laser Detectors and check both laser compatibility and clamp fit before buying.
2. Instrument Tripod
Where a mounting pole cannot be secured, compatible Bosch Laser Level Tripods provide freestanding support. Check the thread, load capacity and working height rather than relying on the brand name alone.
Choose the Right Bosch Laser Accessory for the Job
Start with whether you need to see the beam, measure a height or support the laser.
| Your Job | Accessory Type | Key Features |
|---|---|---|
| Check indoor fitting reference lines | Bosch laser target plate | Suitable beam colour and clearly marked reference surface |
| Check ground heights with a receiver | Bosch laser staff | Compatible receiver clamp and sufficient usable length |
| Take optical level readings | Bosch measuring staff | Suitable graduations and secure extending sections |
| Set an indoor laser at different heights | Bosch laser pole | Correct height range, mounting thread and bracket |
Common Buying and Usage Mistakes
- Buying a target plate for long-range daylight detection can leave you unable to find the beam. Check whether your laser supports a compatible electronic receiver.
- Confusing a mounting pole with a measuring staff leaves you with the wrong accessory. One supports the instrument; the other provides a reference at the measuring point.
- Taking readings with a leaning staff introduces height errors. Keep it vertical and use a staff bubble where suitable.
- Assuming all Bosch fittings match can mean an unusable clamp or bracket. Check the individual accessory and instrument specifications.
Bosch Laser Target vs Measuring Staff vs Mounting Pole
Laser Target Plate
Choose a target for checking a visible beam against a marked surface during fitting and alignment. It is compact, but it cannot provide electronic beam detection in strong daylight.
Measuring Staff
Choose a staff for height readings across groundworks or floor areas. Depending on its design, it supports optical readings or a receiver clamp, but it is not a stand for the laser itself.
Mounting Pole
Choose a compatible pole to adjust an indoor laser's working height without spreading tripod legs across the floor. Pressure-fit designs need suitable, stable surfaces above and below.
Maintenance and Care
Keep Target Markings Clear
Wipe dust and splashes off the target with a soft damp cloth. Avoid abrasive cleaning that could damage its surface or obscure reference markings.
Clean Extending Sections
Remove grit and mud before retracting a staff or pole. Check that each locking section holds securely before taking readings or mounting the laser.
Check Clamps and Brackets
Inspect threads, clamp pads and brackets for damage. Stop using parts that slip or will not tighten properly, and replace them with compatible components.
Store Straight and Dry
Dry accessories before storage and protect them from loose tools in the van. Check any bent staff or pole before reuse, as damage can affect readings or stability.
Shop Bosch Laser Targets, Staffs and Poles at ITS
Shop the full Bosch target, staff and pole range at ITS, with options for beam checks, height readings and instrument support. Stock is held in our own warehouse, with in-stock items ready for next-day delivery. Check current availability and delivery options when ordering.
Bosch Laser Target and Staff FAQs
What is a laser staff used for?
A laser staff provides a support and height reference for a compatible receiver when checking levels. Place its foot on the point being measured and keep it vertical. Graduated measuring staffs may also be used with optical levels, depending on their design.
What is a laser target plate?
It is a marked surface used to locate and compare a laser line or spot. A suitable plate can make the beam easier to distinguish than it is on the work surface, but it is not an electronic detector. Check suitability for your beam colour.
Do Bosch laser levels need a staff and pole?
No. A staff is useful for receiver-based height checks, while a mounting pole supports compatible instruments indoors. Many alignment jobs only need the laser and a suitable bracket or tripod. Buy the accessories required by your method of working.
Are Bosch laser staff any good?
A suitable Bosch staff can serve regular setting-out work, but choose by specification rather than the badge. Check its extended length, graduations, section locks and receiver-clamp compatibility. Even a sound staff gives poor readings if it leans or its sections slip.
Where are Bosch tools made?
Bosch manufactures products in several countries, so there is no single country of origin for the whole range. Check the label or packaging for the specific tool or accessory. A German brand name does not mean every item is made in Germany.
