Vaunt Safety Boots & Trainers
Vaunt SDS drill bits are built for fast, clean holes in concrete, brick and block when a standard masonry bit just will not keep up on site.
If you are drilling fixings all day, knocking through blockwork, or chasing repeated anchor holes, this is the kit you reach for. Vaunt SDS masonry bits and vaunt sds plus drill bits are made for proper hammer drilling, with sizes that suit first fix, brackets, channels and general site drilling. If you need matching gear beyond drilling, see Vaunt, Vaunt SDS Bits and Attachments, Vaunt SDS+, Vaunt SDS+ Chisel Bits and Vaunt Masonry Drill Bits and get the right bits sorted.
What Are Vaunt SDS Drill Bits Used For?
- Drilling repeated fixing holes into concrete lintels, padstones and dense block goes quicker with Vaunt SDS drill bits because the shank and flute design are made for proper rotary hammer work rather than light-duty combi drilling.
- Running first fix in masonry, whether you are fitting conduit clips, trunking, cable tray or pipe brackets, is where vaunt sds plus drill bits earn their keep with clean entry and less wandering on the mark.
- Opening out holes in brick and block for frame fixings, anchors and mechanical fasteners is exactly what vaunt sds masonry bits are for when standard straight shank bits start slowing down or overheating.
- Working through refurb jobs with mixed wall conditions is easier when you have the right vaunt sds bit sizes on hand, so you are not blunting one bit trying to make it do every hole on site.
Choosing the Right Vaunt SDS Drill Bits
Sorting the right bit is simple: match the diameter and working length to the fixing and the wall, not just what happens to be nearest in the case.
1. Pick the Size for the Fixing
If you are drilling for wall plugs and light fixings, stick to the exact size the fixing calls for because loose holes are no use to anyone. If you are on anchors, shield fixings or frame fixings, check the manufacturer size first and buy the proper vaunt sds bit sizes to suit.
2. Match the Length to the Job
If you are only going into plastered block or face brick, a shorter bit is easier to control and usually drills truer. If you are punching through deep masonry, cavity walls or thicker concrete sections, go longer so you are not burying the chuck into the wall and fighting the tool.
3. Single Bits or a Set
If you keep burning through the same few sizes, buy singles and keep spares ready. If your work jumps between different fixings and materials, a vaunt sds drill bit set makes more sense and stops you getting caught short halfway through a first fix.
4. Do Not Force SDS Plus Beyond Its Job
Vaunt SDS+ drill bits are right for most site drilling in brick, block and general concrete. If you are into very large diameters or heavy demolition kit, do not try and make SDS Plus do an SDS Max job because you will only slow the work down and wear the bit out faster.
Who Uses These on Site?
- Sparkies use vaunt sds drill bits for back box fixings, tray supports and repeated holes in block corridors where a normal masonry bit would just waste time.
- Plumbers and heating fitters reach for vaunt sds plus drill bits when mounting clips, brackets and pipe supports into brick or concrete on first fix and plant room work.
- General builders and brickies keep a vaunt sds drill bit set in the van for anchor points, frame fixings and drilling out stubborn masonry during refurbs and extension work.
- Maintenance teams swear by vaunt sds masonry bits for day-to-day drilling in schools, offices and housing stock because they cover the common hole sizes without faffing about between toolboxes.
The Basics: Understanding SDS Drill Bits
These bits are made to work with rotary hammers, not standard drill chucks. The key thing is how the shank locks in, how the hammer action hits the tip, and why that matters when you are drilling masonry all day.
1. SDS Plus Shank
The SDS Plus shank slides and locks into the drill so the tool can hammer properly without the bit slipping in the chuck. On site that means faster drilling in brick, block and concrete with less wasted effort from the user.
2. Masonry Cutting Tip
The tip is built to break and cut through hard mineral materials rather than slice like a wood or metal bit. That is why vaunt sds masonry bits are the right choice for repetitive fixing holes and general building work.
3. Flutes Clear the Dust
The spiral flutes drag dust back out of the hole while you drill. If the dust clears properly, the bit keeps cutting, the hole stays cleaner, and you are less likely to glaze the tip by leaning on it too hard.
SDS Accessories That Keep the Job Moving
A few sensible add-ons save time, keep holes cleaner and stop your drilling setup letting you down halfway through the day.
1. SDS Chisel Bits
When the hole is drilled but the wall still needs chasing out or stubborn material breaking back, SDS chisel bits save you reaching for another machine. Handy for light channel work, tile removal and knocking off proud sections around fixings.
2. Drill Bit Sets and Spare Common Sizes
A full vaunt sds bit set covers the usual site sizes, but keeping spare 5mm, 6mm, 8mm and 10mm bits stops the whole job stalling when one finally dulls out in dense concrete.
3. Depth Stops or Drilling Guides
These stop you overdrilling repeated anchor holes and save time on second fix and bracket runs where every fixing depth wants to be the same.
Choose the Right Vaunt SDS Drill Bits for the Job
Use this quick guide to match the bit to the wall and the fixing.
| Your Job | Category or Type | Key Features |
|---|---|---|
| Wall plugs and light fixings in brick or block | Short Vaunt SDS Plus drill bits | Common small diameters, easy control, fast clean drilling for repeated fixing holes |
| Bracket fixing and first fix support work | Mid length Vaunt SDS masonry bits | Good reach, steady drilling in block and concrete, suits regular trade use |
| Frame fixings and deeper penetrations | Long Vaunt SDS concrete bits | Extra working length, clears dust well, avoids the chuck fouling the wall |
| Mixed day to day site drilling | Vaunt SDS drill bit set | Range of vaunt sds bit sizes in one case, quicker to grab the right diameter |
Common Buying and Usage Mistakes
- Buying one long bit for every job sounds sensible until you are trying to drill neat shallow holes all day. Shorter bits are easier to control, usually drill straighter and put less strain on you and the tool.
- Using a worn SDS bit because it still sort of cuts just slows the whole job down. If the tip is rounded off and progress drops right back, replace it before you cook the drill or ruin fixing accuracy.
- Guessing hole size for plugs and anchors is a classic waste of time. Drill to the fixing manufacturer's size or you end up with loose fixings, blown holes and extra making good.
- Leaning too hard on the drill does not make SDS bits cut faster. Let the hammer action do the work, back off now and then to clear dust, and the bit will run cooler and last longer.
- Mixing up SDS Plus with other shank types catches plenty of buyers out. Check your drill takes SDS Plus before ordering vaunt sds plus drill bits or they simply will not fit.
SDS Plus Drill Bits vs Straight Shank Masonry Bits vs SDS Max Bits
Vaunt SDS Plus Drill Bits
This is the sweet spot for most trade drilling in brick, block and concrete. They fit SDS Plus rotary hammers, drill faster than standard masonry bits, and cover the bulk of fixing, bracket and first fix work on site.
Straight Shank Masonry Bits
Fine for lighter work in a combi drill and handy when you are only doing the odd hole. They are not the best choice for repeated drilling into hard concrete or dense block, where progress slows and heat builds quickly.
SDS Max Bits
These are for bigger machines, heavier concrete work and larger hole demands. If your day is mainly fixings and general building holes, SDS Max is more tool and weight than you need.
Maintenance and Care
Clear Dust After Use
Brush off the flutes and tip after drilling, especially after concrete. Letting dust bake on just hides wear and makes the next use harder work.
Check the Tip Before Big Jobs
If the carbide tip looks chipped, rounded or uneven, swap it out before starting a run of holes. A tired bit gives poor accuracy and puts extra load on the drill.
Keep the Shank Clean
Wipe the SDS shank before putting it back in the box or into the drill. Clean engagement helps the bit seat properly and stops grit wearing the chuck out faster than it should.
Store by Size
Keep bits in a case or rack by diameter and length so you are not chucking sharp tips loose in the van. It also stops wasted time hunting for the right bit on site.
Why Shop for Vaunt SDS Drill Bits at ITS?
Whether you need individual vaunt sds masonry bits, vaunt sds plus drill bits in common fixing sizes, or a full vaunt sds drill bit set for day to day site work, we have the range covered. It is all stocked in our own warehouse, ready for fast next day delivery, so you can get the right bits on the van without hanging about.
Vaunt SDS Drill Bits FAQs
What SDS drill bits does Vaunt make?
Vaunt makes SDS Plus drill bits for masonry drilling in brick, block and concrete, along with sets covering the sizes most trades actually use. The range is aimed at general site drilling, fixings and first fix work rather than specialist oversized core drilling.
What sizes are available in Vaunt SDS drill bits?
Vaunt SDS drill bits are available in a spread of common diameters and lengths suited to plugs, anchors, brackets and frame fixings. The exact vaunt sds bit sizes vary by product line, so check both diameter and working length before you buy, especially if you are drilling through thicker walls or deeper set fixings.
Are Vaunt SDS drill bits compatible with all SDS Plus drills?
Yes, if your machine takes SDS Plus shanks, Vaunt SDS Plus drill bits should fit as they should. They are not for standard three jaw chucks and they are not SDS Max bits, so check the drill type before ordering if you are replacing older accessories.
What materials can Vaunt SDS drill bits be used on?
They are built for masonry materials such as brick, block, stone and concrete. For timber, metal or tile, use the proper bit for that material instead, because an SDS masonry bit is designed for hammer drilling mineral surfaces, not clean cutting in everything else.
Will these hold up for daily site use, or are they just for the odd hole?
They are made for regular trade drilling, not just occasional DIY use. That said, bit life always comes down to what you are drilling, how hard you push and whether you replace them once the tip has gone off rather than trying to squeeze another week out of them.
Is it worth buying a Vaunt SDS drill bit set instead of singles?
Yes, if your work changes from one fixing size to the next through the day. A set saves time and keeps the common diameters together, but if you know you hammer through one or two sizes every week, buy spare singles as well so the job does not stop when one goes blunt.
