Bosch SDS MAX Other Bits and Accessories
Breaking out concrete or changing attachments? Bosch SDS max accessories help match your hammer to the job.
Choose Bosch SDS max chisels and points for controlled breaking, or a compatible adaptor for a different tool fitting. Check the shank, operating mode and machine limits before buying. Find the attachment your job needs below.
What Are Bosch SDS Max Accessories Used For?
- Break up concrete around redundant posts and damaged slab edges using a pointed chisel in a compatible hammer with a chiselling mode.
- Remove mortar and break back masonry during refurbs using a flat chisel sized for the area you need to clear.
- Lift tiles and strip surface material using a suitable wide or angled chisel, keeping the cutting edge shallow to limit damage underneath.
- Adapt an SDS max machine to an explicitly supported accessory fitting when the adaptor and hammer instructions permit that combination.
Choosing the Right Bosch SDS Max Accessories
Match the fitting first, then choose the working end for the material you need to remove.
1. Check the Tool Holder
If your machine takes SDS max, choose an SDS max shank. SDS plus and hex attachments do not fit directly. Check the individual specifications when choosing from Bosch SDS Drills, because the SDS name alone does not confirm the fitting.
2. Choose a Point, Flat Edge or Scraper
Use a point to concentrate impact for localised breaking. Pick a flat chisel for breaking back edges and removing mortar, or a suitable wide scraper for lifting surface coverings. Browse Bosch SDS MAX Chisel Bits by working width and intended material, not just overall length.
3. Read the Adaptor Restrictions
If you need a Bosch SDS max adaptor, confirm both its machine-side and accessory-side connections. Only use the operating modes and accessory sizes approved for that adaptor; it does not make every smaller attachment suitable for a larger hammer.
Who Uses Bosch SDS Max Accessories?
Groundworkers use points for localised concrete breaking, while builders and refurbishment teams use flat chisels to remove masonry and mortar. Fitters stripping tiled floors need an appropriate scraping chisel rather than a narrow point that digs into the substrate. For dedicated breaking work, check the tool holder on Bosch Breakers & Demolition Drills before choosing attachments.
The Basics: Understanding SDS Max Fittings
SDS max describes the attachment connection, not a guarantee that every accessory suits every machine or operating mode.
1. A Sliding, Locked Shank
The tool holder retains the grooved shank while allowing the movement needed for hammer action. Insert the attachment as instructed and check it is securely retained before starting work.
2. Drilling and Chiselling Are Different Jobs
Chisels and points work in hammer-only mode on a machine that supports chiselling. For holes in masonry, use a suitable rotary hammer and Bosch SDS MAX Drill Bits. A chisel is not a drilling attachment.
Keep SDS Max Attachments Working Properly
The right supporting kit helps protect the tool holder and manage dust at the work area.
1. Suitable Shank Grease
Use the grease specified by the machine manufacturer, in the stated amount. A clean, correctly lubricated shank helps reduce wear; packing the holder with excess grease only attracts dirt.
2. Compatible Dust Collection Attachments
Check Bosch Drill Dust Collection Attachments for a system explicitly suited to your machine and task. A drilling attachment is not automatically suitable for chiselling, and collection equipment must be paired with appropriate extraction and other controls identified by the dust assessment.
Choose the Right Bosch SDS Max Accessories for the Job
Start with the material and the shape of the area you need to remove.
| Your Job | Accessory Type | Key Features |
|---|---|---|
| Localised concrete breaking | SDS max point | Pointed working end concentrates impact in a small area. |
| Breaking back masonry edges | SDS max flat chisel | Cutting width matched to the edge and access available. |
| Lifting tiles or surface coverings | Suitable tile or scraping chisel | Wide or angled working end designed for stripping. |
| Connecting a different accessory fitting | Compatible SDS max adaptor | Correct connections and explicit approval for the intended operating mode. |
Common Buying and Usage Mistakes
- Buying by the SDS name alone leads to incompatible kit. Check for SDS max rather than SDS plus, and confirm the machine specification.
- Running a chisel in a rotating mode gives poor control and can cause damage. Select hammer-only mode as instructed by the machine manufacturer.
- Using a narrow point to strip a broad tiled floor gouges the substrate and slows progress. Choose a suitable scraping chisel instead.
- Treating an adaptor as permission to use any attachment risks overloading the accessory. Follow its capacity and operating-mode restrictions.
SDS Max Points vs Flat Chisels vs Scraping Chisels
Points for Concentrated Breaking
Bosch SDS max points concentrate impact for starting localised breaks in concrete and masonry. Choose one for breaking, not for leaving a clean, broad surface.
Flat Chisels for Defined Edges
A flat chisel works across a cutting edge rather than a single point. It suits breaking back masonry and removing mortar, but a narrow version is slow for stripping a large floor.
Scraping Chisels for Surface Removal
A suitable wide or angled scraper gets underneath tiles and surface layers. Choose it for stripping rather than deep concrete breaking, and check its approved materials before use.
Maintenance and Care
Clean Before Refitting
Remove grit and masonry dust from the shank before insertion. Let hot attachments cool before handling, cleaning or storing them.
Check for Damage
Inspect the shank and working end for cracks, distortion and excessive wear. Stop using damaged attachments; only resharpen where the accessory instructions permit it.
Store Dry and Secure
Keep attachments dry and separated from loose rubble in the van. Follow the manufacturer's corrosion-protection advice and keep adaptor connections clean so they seat correctly.
Shop Bosch SDS Max Accessories at ITS
ITS stocks the Bosch SDS max accessories range, covering points, chisels and compatible adaptors so you can match the attachment to your machine and job. Stock is held in our own warehouse, with in-stock lines ready for next-day delivery. Check individual listings for availability and delivery options before ordering.
Bosch SDS Max Accessories FAQs
What SDS max accessories does Bosch make?
Bosch makes SDS max drilling and chiselling accessories, including pointed, flat and application-specific chisels, alongside selected adaptors. Check each listing for its intended material, dimensions and machine requirements; not every attachment suits every breaking or stripping task.
What is an SDS max adaptor used for?
It connects an SDS max tool holder to a different supported accessory fitting. The exact function depends on the adaptor. Confirm both connections, permitted operating modes and accessory limits before buying; an adaptor does not remove the smaller accessory's limitations.
Do Bosch SDS max accessories fit any breaker?
No. They require a compatible SDS max tool holder and a machine approved for the intended task. Breakers with hex or SDS plus holders will not accept them directly. A matching fitting is only the first check; attachment size and operating mode also matter.
Are Bosch sds max accessories any good?
They are a practical option for compatible SDS max machines, but the individual accessory matters more than the name alone. Choose the right working profile and material application. Even a suitable chisel will perform poorly if it is worn, forced sideways or used for the wrong task.
Where are Bosch tools made?
Bosch manufactures across several countries, and the country of origin varies by product. Do not assume every Bosch tool or accessory is made in Germany. Check the specific item's marking or packaging, or confirm the exact product details before ordering if origin is a purchasing requirement.
