Makita Glass & Tile Cutters
Makita tile cutter range for clean, controlled cuts in porcelain, ceramic and glass, without chipping edges or burning blades.
When you're fitting kitchens, bathrooms, or doing snag cuts on a refurb, a decent Makita tile saw saves you time and wasted tiles. From a Makita 18V tile cutter for quick site work to a glass and tile cutter for delicate trims, pick the size and setup that matches your day-to-day cuts and water control.
What Are Makita Tile Cutters Used For?
- Cutting porcelain and ceramic floor tiles cleanly for bathrooms and kitchens, especially where you need straight lines that don't wander and edges that don't chip.
- Trimming glass mosaic and splashback tiles with controlled feed and a proper diamond blade, so you are not snapping expensive pieces on the last cut.
- Doing quick on-site adjustments around door linings, pipe boxing, and awkward returns where a manual score-and-snap just will not give you the finish.
- Wet cutting to keep dust down and blades cooler when you are batch-cutting tiles for a full room, which helps the cut stay cleaner and the blade last longer.
- Repair and maintenance work where you need a compact Makita 18V tile cutter that comes out the van fast and gets one or two tiles cut without setting up a full bench.
Choosing the Right Makita Tile Cutter
Match the cutter to what you cut most, not the odd one-off job, because tile type and size will punish the wrong setup fast.
1. Tile Type and Finish
If you are mainly on porcelain, go for a Makita tile saw setup that runs a proper diamond blade and keeps the cut stable, because porcelain chips when the tool flexes or the blade is tired. If you are doing glass and tile cutter work, prioritise controlled cutting and clean support to stop breakout on the face.
2. Cordless 18V vs Corded
If you are moving room to room, working in occupied homes, or you just want fast setup, a Makita 18V tile cutter makes sense because you are not hunting sockets and trailing leads through finished areas. If you are batch cutting all day, corded can still be the steadier choice for long, continuous runs.
3. Cut Capacity and Handling
If you regularly cut larger format tiles, check the maximum cut length and depth before you buy, because forcing a tile through a cutter that is too small is how you crack corners and ruin edges. For small trims and repairs, a compact body is quicker to set and easier to control on fiddly cuts.
Makita Tile Cutter FAQs
What is the Makita dcc500 18V tile cutter?
It is Makita's 18V cordless tile cutter designed for cutting ceramic, porcelain, and similar materials on site without needing a mains supply. It is built for controlled, accurate cuts where a manual cutter will not give you the finish, especially on harder tiles.
Is a Makita 18V tile cutter powerful enough for porcelain?
Yes, for most site cuts it will handle porcelain fine, but the blade condition and the way you feed the cut matter. If you force it or run a tired blade, porcelain will chip and the tool will feel like it is struggling.
Do I need wet cutting, or can I just cut dry?
If you are doing lots of cuts, wet cutting is the sensible option because it keeps dust down and stops the blade overheating, which helps the edge stay cleaner. Dry cutting is fine for quick trims, but you need proper dust control and you should expect faster blade wear.
Will a Makita tile saw cut glass tiles without chipping?
It can, but do not try it with a general blade and expect miracles. Use a blade suited to glass and keep the tile properly supported, because glass chips right at the end of the cut if it is vibrating or flexing.
What usually causes rough edges and chipped corners?
Nine times out of ten it is a worn or wrong blade, pushing too hard, or poor support under the tile. Slow the feed, keep the blade cool, and make sure the tile is flat and stable right through the cut.
Who Are These For on Site?
- Tilers fitting porcelain, ceramic, and natural stone who need a Makita tile cutter that holds a straight cut and leaves a tidy edge for tight grout lines.
- Bathroom and kitchen fitters doing constant trims around units, trims, and penetrations, where a Makita tile saw stops you wasting tiles on awkward shapes.
- Maintenance teams and snagging crews who need a reliable glass and tile cutter for replacements, patch-ins, and matching existing finishes without making a mess.
The Basics: Understanding Tile Saws and Glass and Tile Cutters
Tile cutting is all about keeping the blade cool, the tile supported, and the cut steady, so the edge stays clean and you do not burn through blades.
1. Wet Cutting vs Dry Cutting
Wet cutting feeds water to the blade to control dust and heat, which helps stop chipping and keeps the blade cutting clean, especially on porcelain. Dry cutting is quicker to deploy for small jobs, but it is messier and you need to be realistic about dust control and blade wear.
2. Blade Choice Is Half the Result
A decent diamond blade matched to ceramic, porcelain, or glass is what gives you a tidy edge. If the cut starts chipping or wandering, it is usually the blade or the support, not your hands.
3. Support and Straight Tracking
The cleaner the support under the tile and the steadier the tracking, the less chance of breakout on the last few millimetres. That matters most on visible edges, mitres, and glass where you cannot hide a bad cut.
Tile Saw Accessories That Save Tiles and Time
The right add-ons stop chipping, reduce rework, and keep your cutter running properly through a full room.
1. Diamond Blades for Tile and Glass
Keep a fresh blade ready, because a worn diamond blade is what starts chipping edges and overheating on porcelain. Use the right blade type for glass if you want clean faces without breakout.
2. Water Feed and Reservoir Parts
If you are wet cutting, clogged feeds and dirty trays ruin cut quality fast. Spare or replacement water system parts keep flow consistent so the blade stays cool and the cut stays clean.
3. Clamps, Guides, and Support Tables
Extra support and a solid guide make a bigger difference than you think on long cuts and mitres, especially on large format tiles where flex is what cracks corners.
Shop Makita Tile Cutters at ITS
Whether you need a compact Makita 18V tile cutter for quick site cuts or a Makita tile saw setup for regular bathroom and kitchen work, we stock the full range to suit different tile types and cut sizes. It is all held in our own warehouse, in stock and ready for next day delivery so you can get cutting on tomorrow's job.
