Festool Router Tables & Accessories
A Festool router table is for when handheld routing just is not accurate enough for repeat work and clean edges on site or in the workshop.
When you are batching up hinge recesses, trimming lippings, or running a consistent profile on multiple parts, a Festool router table setup gives you proper control and safe, repeatable feeding. Pick the right table and accessories for your router and the way you work, and you will get joinery-grade results without the faff.
What Jobs Are Festool Router Tables Best At?
- Routing repeatable edge profiles on doors, panels, and worktops when you need the same finish every time without the wobble you get freehand.
- Trimming lippings and laminate flush on sheet material where a stable table and fence stops you tipping the router and chewing an edge.
- Cutting grooves and rebates for cabinet backs, drawer bottoms, and panel work when you want straight, consistent depth runs across multiple components.
- Working small parts safely by bringing the cutter to the work, so your hands stay clear and the piece stays supported instead of snatching.
Choosing the Right Festool Router Table
Sort the right Festool router table by matching it to the router you own and the way you feed the work, not just what looks tidy on the bench.
1. Router compatibility and mounting
If your router is not supported by the table insert or mounting set-up, you will waste time bodging it and fighting alignment. Check the exact router models the table is designed for before you buy, especially if you are swapping between routers on different jobs.
2. Fence and adjustment control
If you are doing grooves, rebates, and edge work all week, you want a fence that locks square and adjusts predictably, so you are not tapping it with a mallet and re-measuring every cut. For occasional trimming, a simpler fence set-up can be fine.
3. Work support for small parts
If you regularly run narrow lippings, short rails, or small components, look at accessories that increase support and control during the feed. That is what stops chatter, snatch, and burn marks when the piece is too small to hold comfortably.
Who Uses Festool Router Tables?
- Joiners and chippies doing kitchens, built-ins, and second fix who need repeatable routing without setting up a big spindle moulder.
- Shopfitters batching trims, edging, and panels where a router table keeps the work consistent across a full run.
- Site carpenters and bench teams who want cleaner control on small or awkward pieces that are a pain to hold steady with a handheld router.
How a Festool Router Table Works for You
A router table flips the job around: the router stays fixed and you guide the timber. That is why it feels steadier, safer, and more repeatable for batch work.
1. Fixed cutter, controlled feed
With the router mounted under the table, you are feeding the work past the cutter using the fence as your reference. On real jobs, that means straighter runs and less chance of tipping the base and ruining an edge.
2. Fence sets the line, height sets the finish
The fence position controls how much material you remove, and the cutter height controls the depth or profile. Once it is dialled in, you can repeat cuts across a full stack of parts without constantly re-setting the router.
3. Accessories make it a proper system
Things like better work support, guides, and table-specific fittings are what turn it from a one-off set-up into something you can rely on day to day, especially when you are working to tight tolerances.
Festool Router Table Accessories That Make the Setup Work
The right add-ons stop the usual router table headaches like poor support, awkward feeding, and wasting time re-aligning.
1. Router table inserts and mounting plates
Get the correct insert or plate for your router so it sits square and solid under the table. It saves you fighting alignment and keeps cutter height and fence settings consistent from one job to the next.
2. Sliding carriage and support attachments
If you are machining smaller parts or want more controlled, straight feeding, a sliding carriage style accessory is the difference between smooth passes and a piece that chatters or snatches as it hits the cutter.
3. Table fences and guide upgrades
A proper fence that locks square and adjusts cleanly saves loads of time when you are swapping between edge profiling and grooving. It also helps you avoid the classic problem of a fence creeping mid-pass and ruining the run.
Shop Festool Router Tables and Accessories at ITS
Whether you need a Festool router table setup for repeat routing or just the specific accessories to suit your router and the jobs you do, we have the range ready to pick from. It is all stocked in our own warehouse and ready for next day delivery, so you can get set up and crack on.
Festool Router Table FAQs
Can I mount any Festool router to the CMS router table?
No, not every Festool router mounts straight on without the correct insert or mounting set-up. Check the exact router models listed for the CMS table and make sure you are buying the right plate or fitting kit, otherwise you will be stuck with a router that will not sit securely or line up properly.
Does the Festool router table include a sliding carriage?
Not always. Some Festool router table setups are sold as the table and core fittings, with the sliding carriage available as an accessory depending on the configuration. If you need controlled feeding for small parts or repeat work, check the box contents and add the carriage if it is not included.
Is a router table actually worth it if I already use a guide rail and handheld router?
Yes, if you are doing repeated edge work, lippings, or profiling where consistency matters. A guide rail is great for straight runs, but a router table is what gives you steady, repeatable feeding and cleaner control on smaller pieces that are awkward to hold freehand.
What is the common mistake that ruins results on a router table?
Pushing too hard in one pass and feeding inconsistently is the big one, especially on hardwoods and lippings. Set the fence properly, take sensible passes, and keep the work supported so it does not dip or twist as it hits the cutter.
